diff --git b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt new file mode 100644 index 0000000..ebf0d47 --- /dev/null +++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt @@ -0,0 +1,48 @@ +The generic power sequence library + +Some hard-wired devices (eg USB/MMC) need to do power sequence before +the device can be enumerated on the bus, the typical power sequence +like: enable USB PHY clock, toggle reset pin, etc. But current +Linux device driver lacks of such code to do it, it may cause some +hard-wired devices works abnormal or can't be recognized by +controller at all. The power sequence will be done before this device +can be found at the bus. + +The power sequence properties is under the device node. + +Optional properties: +- clocks: the input clocks for device. +- reset-gpios: Should specify the GPIO for reset. +- reset-duration-us: the duration in microsecond for assert reset signal. + +Below is the example of USB power sequence properties on USB device +nodes which have two level USB hubs. + +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + genesys: hub@1 { + compatible = "usb5e3,608"; + reg = <1>; + + clocks = <&clks IMX6SX_CLK_CKO>; + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */ + reset-duration-us = <10>; + + #address-cells = <1>; + #size-cells = <0>; + asix: ethernet@1 { + compatible = "usbb95,1708"; + reg = <1>; + + clocks = <&clks IMX6SX_CLK_IPG>; + reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */ + reset-duration-us = <15>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt index 036be17..cb85f82 100644 --- a/Documentation/devicetree/bindings/usb/usb-device.txt +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -65,6 +65,9 @@ Required properties for host-controller nodes with device nodes: - #address-cells: shall be 1 - #size-cells: shall be 0 +Optional properties: +power sequence properties, see +Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt for detail Example: @@ -72,9 +75,13 @@ Example: #address-cells = <1>; #size-cells = <0>; - hub@1 { /* hub connected to port 1 */ + genesys: hub@1 { /* hub connected to port 1 */ compatible = "usb5e3,608"; reg = <1>; + + clocks = <&clks IMX6SX_CLK_CKO>; + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */ + reset-duration-us = <10>; }; device@2 { /* device connected to port 2 */ diff --git b/Documentation/power/power-sequence/design.rst b/Documentation/power/power-sequence/design.rst new file mode 100644 index 0000000..554608e --- /dev/null +++ b/Documentation/power/power-sequence/design.rst @@ -0,0 +1,54 @@ +==================================== +Power Sequence Library +==================================== + +:Date: Feb, 2017 +:Author: Peter Chen + + +Introduction +============ + +We have an well-known problem that the device needs to do a power +sequence before it can be recognized by related host, the typical +examples are hard-wired mmc devices and usb devices. The host controller +can't know what kinds of this device is in its bus if the power +sequence has not done, since the related devices driver's probe calling +is determined by runtime according to eunumeration results. Besides, +the devices may have custom power sequence, so the power sequence library +which is independent with the devices is needed. + +Design +============ + +The power sequence library includes the core file and customer power +sequence library. The core file exports interfaces are called by +host controller driver for power sequence and customer power sequence +library files to register its power sequence instance to global +power sequence list. The custom power sequence library creates power +sequence instance and implement custom power sequence. + +Since the power sequence describes hardware design, the description is +located at board description file, eg, device tree dts file. And +a specific power sequence belongs to device, so its description +is under the device node, please refer to: +Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt + +Custom power sequence library allocates one power sequence instance at +bootup periods using postcore_initcall, this static allocated instance is +used to compare with device-tree (DT) node to see if this library can be +used for the node or not. When the result is matched, the core API will +try to get resourses (->get, implemented at each library) for power +sequence, if all resources are got, it will try to allocate another +instance for next possible request from host driver. + +Then, the host controller driver can carry out power sequence on for this +DT node, the library will do corresponding operations, like open clocks, +toggle gpio, etc. The power sequence off routine will close and free the +resources, and is called when the parent is removed. And the power +sequence suspend and resume routine can be called at host driver's +suspend and resume routine if needed. + +The exported interfaces +.. kernel-doc:: drivers/power/pwrseq/core.c + :export: diff --git a/MAINTAINERS b/MAINTAINERS index bfc1b86..fd492dc 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -14226,6 +14226,15 @@ F: drivers/firmware/psci/ F: include/linux/psci.h F: include/uapi/linux/psci.h +POWER SEQUENCE LIBRARY +M: Peter Chen +T: git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git +L: linux-pm@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/power/pwrseq/ +F: drivers/power/pwrseq/ +F: include/linux/power/pwrseq.h + POWER SUPPLY CLASS/SUBSYSTEM and DRIVERS M: Sebastian Reichel L: linux-pm@vger.kernel.org diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b..00cb939 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,4 +1,9 @@ # SPDX-License-Identifier: GPL-2.0 + +ifeq ($(CONFIG_OF_OVERLAY),y) +DTC_FLAGS += -@ +endif + dtb-$(CONFIG_ARCH_ALPINE) += \ alpine-db.dtb dtb-$(CONFIG_MACH_ARTPEC6) += \ @@ -804,6 +809,9 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-base0033.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-sancloud-bbe-uboot.dtb \ + am335x-boneblack-uboot.dtb \ + am335x-bonegreen-gateway.dtb \ am335x-boneblack-wireless.dtb \ am335x-boneblue.dtb \ am335x-bonegreen.dtb \ @@ -838,6 +846,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-duovero-parlor.dtb \ omap4-kc1.dtb \ omap4-panda.dtb \ + omap4-panda-es-b3.dtb \ omap4-panda-a4.dtb \ omap4-panda-es.dtb \ omap4-sdp.dtb \ @@ -1435,3 +1444,8 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-opp-zaius.dtb \ aspeed-bmc-portwell-neptune.dtb \ aspeed-bmc-quanta-q71l.dtb + +targets += dtbs dtbs_install +targets += $(dtb-y) + +subdir-y := overlays diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 2d51d4b..353401a 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -26,14 +26,14 @@ compatible = "gpio-leds"; led2 { - label = "beaglebone:green:heartbeat"; + label = "beaglebone:green:usr0"; gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; default-state = "off"; }; led3 { - label = "beaglebone:green:mmc0"; + label = "beaglebone:green:usr1"; gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; linux,default-trigger = "mmc0"; default-state = "off"; @@ -63,9 +63,6 @@ }; &am33xx_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&clkout2_pin>; - user_leds_s0: user_leds_s0 { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a5.gpio1_21 */ @@ -96,12 +93,6 @@ >; }; - clkout2_pin: pinmux_clkout2_pin { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; - }; - cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ diff --git b/arch/arm/boot/dts/am335x-bone-jtag.dtsi b/arch/arm/boot/dts/am335x-bone-jtag.dtsi new file mode 100644 index 0000000..19c8bcf --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-jtag.dtsi @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ + */ + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin>; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; +}; diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts index b5d85ef..90a248a 100644 --- a/arch/arm/boot/dts/am335x-bone.dts +++ b/arch/arm/boot/dts/am335x-bone.dts @@ -6,10 +6,16 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone"; compatible = "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-bone.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &ldo3_reg { diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/am335x-boneblack-common.dtsi index 64c3e92..b3cba07 100644 --- a/arch/arm/boot/dts/am335x-boneblack-common.dtsi +++ b/arch/arm/boot/dts/am335x-boneblack-common.dtsi @@ -28,7 +28,6 @@ &am33xx_pinmux { nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0) @@ -52,12 +51,6 @@ >; }; - nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) - >; - }; - mcasp0_pins: mcasp0_pins { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ @@ -93,9 +86,8 @@ nxp,calib-gpios = <&gpio1 25 0>; interrupts-extended = <&gpio1 25 IRQ_TYPE_LEVEL_LOW>; - pinctrl-names = "default", "off"; + pinctrl-names = "default"; pinctrl-0 = <&nxp_hdmi_bonelt_pins>; - pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */ /* video-ports = <0x234501>; */ diff --git b/arch/arm/boot/dts/am335x-boneblack-uboot.dts b/arch/arm/boot/dts/am335x-boneblack-uboot.dts new file mode 100644 index 0000000..80751b0 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-uboot.dts @@ -0,0 +1,184 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-boneblack-uboot.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro-1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&gpio0 { + gpio-line-names = + "[ethernet]", + "[ethernet]", + "P9_22 [spi0_sclk]", + "P9_21 [spi0_d0]", + "P9_18 [spi0_d1]", + "P9_17 [spi0_cs0]", + "[sd card]", + "P9_42A [ecappwm0]", + "P8_35 [hdmi]", + "P8_33 [hdmi]", + "P8_31 [hdmi]", + "P8_32 [hdmi]", + "P9_20 [i2c2_sda]", + "P9_19 [i2c2_scl]", + "P9_26 [uart1_rxd]", + "P9_24 [uart1_txd]", + "[ethernet]", + "[ethernet]", + "[usb]", + "[hdmi]", + "P9_41B", + "[ethernet]", + "P8_19 [ehrpwm2a]", + "P8_13 [ehrpwm2b]", + "[NC]", + "[NC]", + "P8_14", + "P8_17", + "[ethernet]", + "[ethernet]", + "P9_11 [uart4_rxd]", + "P9_13 [uart4_txd]"; +}; + +&gpio1 { + gpio-line-names = + "P8_25 [emmc]", + "[emmc]", + "P8_5 [emmc]", + "P8_6 [emmc]", + "P8_23 [emmc]", + "P8_22 [emmc]", + "P8_3 [emmc]", + "P8_4 [emmc]", + "[NC]", + "[NC]", + "[NC]", + "[NC]", + "P8_12", + "P8_11", + "P8_16", + "P8_15", + "P9_15A", + "P9_23", + "P9_14 [ehrpwm1a]", + "P9_16 [ehrpwm1b]", + "[emmc]", + "[usr0 led]", + "[usr1 led]", + "[usr2 led]", + "[usr3 led]", + "[hdmi]", + "[usb]", + "[hdmi audio]", + "P9_12", + "P8_26", + "P8_21 [emmc]", + "P8_20 [emmc]"; +}; + +&gpio2 { + gpio-line-names = + "P9_15B", + "P8_18", + "P8_7", + "P8_8", + "P8_10", + "P8_9", + "P8_45 [hdmi]", + "P8_46 [hdmi]", + "P8_43 [hdmi]", + "P8_44 [hdmi]", + "P8_41 [hdmi]", + "P8_42 [hdmi]", + "P8_39 [hdmi]", + "P8_40 [hdmi]", + "P8_37 [hdmi]", + "P8_38 [hdmi]", + "P8_36 [hdmi]", + "P8_34 [hdmi]", + "[ethernet]", + "[ethernet]", + "[ethernet]", + "[ethernet]", + "P8_27 [hdmi]", + "P8_29 [hdmi]", + "P8_28 [hdmi]", + "P8_30 [hdmi]", + "[emmc]", + "[emmc]", + "[emmc]", + "[emmc]", + "[emmc]", + "[emmc]"; +}; + +&gpio3 { + gpio-line-names = + "[ethernet]", + "[ethernet]", + "[ethernet]", + "[ethernet]", + "[ethernet]", + "[i2c0]", + "[i2c0]", + "[emu]", + "[emu]", + "[ethernet]", + "[ethernet]", + "[NC]", + "[NC]", + "[usb]", + "P9_31 [spi1_sclk]", + "P9_29 [spi1_d0]", + "P9_30 [spi1_d1]", + "P9_28 [spi1_cs0]", + "P9_42B [ecappwm0]", + "P9_27", + "P9_41A", + "P9_25", + "[NC]", + "[NC]", + "[NC]", + "[NC]", + "[NC]", + "[NC]", + "[NC]", + "[NC]", + "[NC]", + "[NC]"; +}; diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts index 86cad99..31215d4 100644 --- a/arch/arm/boot/dts/am335x-boneblack-wireless.dts +++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts @@ -8,11 +8,17 @@ #include "am335x-bone-common.dtsi" #include "am335x-boneblack-common.dtsi" #include +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Black Wireless"; compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + chosen { + base_dtb = "am335x-boneblack-wireless.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; + wlan_en_reg: fixedregulator@2 { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator"; diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index b4feb85..d1b97cb 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -7,10 +7,16 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" #include "am335x-boneblack-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Black"; compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-boneblack.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &cpu0_opp_table { diff --git a/arch/arm/boot/dts/am335x-boneblue.dts b/arch/arm/boot/dts/am335x-boneblue.dts index 69acaf4..313841f 100644 --- a/arch/arm/boot/dts/am335x-boneblue.dts +++ b/arch/arm/boot/dts/am335x-boneblue.dts @@ -14,6 +14,8 @@ chosen { stdout-path = &uart0; + base_dtb = "am335x-boneblue.dts"; + base_dtb_timestamp = __TIMESTAMP__; }; leds { @@ -128,7 +130,6 @@ AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE7) /* (T5) lcd_data15.gpio0[11] - P8.32, BATT_LED_2 */ AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE7) /* (V6) gpmc_csn0.gpio1[29] - P8.26, BATT_LED_3 */ AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_OUTPUT, MUX_MODE7) /* (T11) gpmc_ad10.gpio0[26] - P8.14, BATT_LED_4 */ - >; }; diff --git b/arch/arm/boot/dts/am335x-bonegreen-gateway.dts b/arch/arm/boot/dts/am335x-bonegreen-gateway.dts new file mode 100644 index 0000000..1c18179 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen-gateway.dts @@ -0,0 +1,209 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-bonegreen-common.dtsi" +#include +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "SeeedStudio BeagleBone Green Gateway"; + compatible = "ti,am335x-bone-green-gateway", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + aliases { + rtc0 = &extrtc; + rtc1 = &rtc; + }; + + chosen { + base_dtb = "am335x-bonegreen-gateway.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; + + wlan_en_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + startup-delay-us= <70000>; + + /* WL_EN */ + gpio = <&gpio3 9 0>; + enable-active-high; + }; + + leds { + pinctrl-0 = <&user_leds_s0 &extra_led_pins>; + + led6 { + label = "beaglebone:green:usr4"; + gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "netdev"; + default-state = "off"; + }; + }; +}; + +&cpu0_opp_table { + /* + * Octavo Systems: + * The EFUSE_SMA register is not programmed for any of the AM335x wafers + * we get and we are not programming them during our production test. + * Therefore, from a DEVICE_ID revision point of view, the silicon looks + * like it is Revision 2.1. However, from an EFUSE_SMA point of view for + * the HW OPP table, the silicon looks like it is Revision 1.0 (ie the + * EFUSE_SMA register reads as all zeros). + */ + oppnitro-1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&usbhost_pins>; + + bt_pins: pinmux_bt_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gmii1_txd0.gpio0_28 - BT_EN */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLUP, MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */ + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLUP, MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */ + AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */ + >; + }; + + uart2_grove_pins: pinmux_uart2_grove_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x90c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) + AM33XX_IOPAD(0x910, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1) /* gmii1_rxd3.uart3_rxd */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* gmii1_rxd2.uart3_txd */ + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT, MUX_MODE3) /* mdio_data.uart3_ctsn */ + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* mdio_clk.uart3_rtsn */ + >; + }; + + extra_led_pins: pinmux_extra_led_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_OUTPUT, MUX_MODE7) /* WL_Active_LED / USR4 */ + >; + }; + + wl18xx_pins: pinmux_wl18xx_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gmii1_txclk.gpio3_9 WL_EN */ + AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) /* rmii1_refclk.gpio0_29 WL_IRQ */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gmii1_rxclk.gpio3_10 LS_BUF_EN */ + >; + }; + + usbhost_pins: pinmux_usbhost_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_txd1.gpio0[21] */ + >; + }; +}; + +&mac { + status = "disabled"; +}; + +&mmc3 { + dmas = <&edma_xbar 12 0 1 + &edma_xbar 13 0 2>; + dma-names = "tx", "rx"; + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + non-removable; + cap-power-off-card; + keep-power-in-suspend; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins &wl18xx_pins>; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <29 IRQ_TYPE_EDGE_RISING>; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_grove_pins>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins &bt_pins>; + status = "okay"; + + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + }; +}; + +&i2c0 { + extrtc: rtc@68 { + compatible = "dallas,ds1340"; + reg = <0x68>; + }; +}; + +// (K16) gmii1_txd1.gpio0[21] +&gpio0 { + usb_reset { + gpio-hog; + gpios = <21 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb_reset"; + }; +}; + +&gpio3 { + ls_buf_en { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "LS_BUF_EN"; + }; +}; + +&usb1 { + #address-cells = <1>; + #size-cells = <0>; + + hub@1 { + compatible = "usb424,9512"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet: ethernet@1 { + compatible = "usb424,ec00"; + reg = <1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts index 7615327..f75ae32 100644 --- a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts +++ b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts @@ -8,11 +8,17 @@ #include "am335x-bone-common.dtsi" #include "am335x-bonegreen-common.dtsi" #include +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Green Wireless"; compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + chosen { + base_dtb = "am335x-bonegreen-wireless.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; + wlan_en_reg: fixedregulator@2 { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator"; diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/am335x-bonegreen.dts index 18cc0f4..277983f 100644 --- a/arch/arm/boot/dts/am335x-bonegreen.dts +++ b/arch/arm/boot/dts/am335x-bonegreen.dts @@ -7,8 +7,14 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" #include "am335x-bonegreen-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Green"; compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-bonegreen.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; diff --git a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts index f841afb..a2abee5 100644 --- a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts +++ b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts @@ -1,9 +1,6 @@ //SPDX-License-Identifier: GPL-2.0 -/* Copyright (C) 2018 Octavo Systems LLC - https://www.octavosystems.com/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. +/* + * Copyright (C) 2018 Octavo Systems LLC - https://www.octavosystems.com/ */ /dts-v1/; @@ -13,10 +10,16 @@ #include #include +/* #include "am335x-bone-jtag.dtsi" */ / { model = "Octavo Systems OSD3358-SM-RED"; compatible = "oct,osd3358-sm-refdesign", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-osd3358-sm-red.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &ldo3_reg { @@ -40,7 +43,6 @@ &am33xx_pinmux { nxp_hdmi_bonelt_pins: nxp-hdmi-bonelt-pins { pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0) @@ -64,12 +66,6 @@ >; }; - nxp_hdmi_bonelt_off_pins: nxp-hdmi-bonelt-off-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) - >; - }; - mcasp0_pins: mcasp0-pins { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) @@ -124,9 +120,8 @@ compatible = "nxp,tda998x"; reg = <0x70>; - pinctrl-names = "default", "off"; + pinctrl-names = "default"; pinctrl-0 = <&nxp_hdmi_bonelt_pins>; - pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */ /* video-ports = <0x234501>; */ @@ -264,9 +259,6 @@ }; &am33xx_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&clkout2_pin>; - user_leds_s0: user-leds-s0 { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a5.gpio1_21 */ @@ -290,12 +282,6 @@ >; }; - clkout2_pin: pinmux-clkout2-pin { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; - }; - cpsw_default: cpsw-default { pinctrl-single,pins = < /* Slave 1 */ diff --git a/arch/arm/boot/dts/am335x-pocketbeagle.dts b/arch/arm/boot/dts/am335x-pocketbeagle.dts index d526c59..20e998e 100644 --- a/arch/arm/boot/dts/am335x-pocketbeagle.dts +++ b/arch/arm/boot/dts/am335x-pocketbeagle.dts @@ -15,6 +15,8 @@ chosen { stdout-path = &uart0; + base_dtb = "am335x-pocketbeagle.dts"; + base_dtb_timestamp = __TIMESTAMP__; }; leds { diff --git b/arch/arm/boot/dts/am335x-sancloud-bbe-uboot.dts b/arch/arm/boot/dts/am335x-sancloud-bbe-uboot.dts new file mode 100644 index 0000000..8d8982f --- /dev/null +++ b/arch/arm/boot/dts/am335x-sancloud-bbe-uboot.dts @@ -0,0 +1,151 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include + +/ { + model = "SanCloud BeagleBone Enhanced"; + compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-sancloud-bbe-uboot.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0) + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + usb_hub_ctrl: usb_hub_ctrl { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_OUTPUT_PULLUP, MUX_MODE7) /* rmii1_refclk.gpio0_29 */ + >; + }; + + mpu6050_pins: pinmux_mpu6050_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT, MUX_MODE7) /* uart0_ctsn.gpio1_8 */ + >; + }; + + lps3331ap_pins: pinmux_lps3331ap_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT, MUX_MODE7) /* gpmc_a10.gpio1_26 */ + >; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +&cpsw_emac0 { + phy-handle = <ðphy0>; + phy-mode = "rgmii-id"; +}; + +&i2c0 { + lps331ap: barometer@5c { + compatible = "st,lps331ap-press"; + st,drdy-int-pin = <1>; + reg = <0x5c>; + interrupt-parent = <&gpio1>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + }; + + mpu6050: accelerometer@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + interrupt-parent = <&gpio0>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + orientation = <0xff 0 0 0 1 0 0 0 0xff>; + }; + + usb2512b: usb-hub@2c { + compatible = "microchip,usb2512b"; + reg = <0x2c>; + reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + /* wifi on port 4 */ + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/am335x-sancloud-bbe.dts index 275ba33..0a80f58 100644 --- a/arch/arm/boot/dts/am335x-sancloud-bbe.dts +++ b/arch/arm/boot/dts/am335x-sancloud-bbe.dts @@ -12,6 +12,11 @@ / { model = "SanCloud BeagleBone Enhanced"; compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-sancloud-bbe.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &am33xx_pinmux { diff --git a/arch/arm/boot/dts/am5729-beagleboneai.dts b/arch/arm/boot/dts/am5729-beagleboneai.dts index 149cfaf..6247721 100644 --- a/arch/arm/boot/dts/am5729-beagleboneai.dts +++ b/arch/arm/boot/dts/am5729-beagleboneai.dts @@ -26,6 +26,8 @@ chosen { stdout-path = &uart1; + base_dtb = "am5729-beagleboneai.dts"; + base_dtb_timestamp = __TIMESTAMP__; }; memory@0 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts index 83e174e..0ba9202 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts @@ -7,6 +7,11 @@ / { model = "TI AM5728 BeagleBoard-X15 rev B1"; + + chosen { + base_dtb = "am57xx-beagle-x15-revb1.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &tpd12s015 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts index 656dd84..9c721c0 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts @@ -7,6 +7,11 @@ / { model = "TI AM5728 BeagleBoard-X15 rev C"; + + chosen { + base_dtb = "am57xx-beagle-x15-revc.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &tpd12s015 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index 0a8b165..028928f 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -8,6 +8,11 @@ / { /* NOTE: This describes the "original" pre-production A2 revision */ model = "TI AM5728 BeagleBoard-X15"; + + chosen { + base_dtb = "am57xx-beagle-x15.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &tpd12s015 { diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts index c63f371..546d9d4 100644 --- a/arch/arm/boot/dts/imx6q-evi.dts +++ b/arch/arm/boot/dts/imx6q-evi.dts @@ -55,18 +55,6 @@ reg = <0x10000000 0x40000000>; }; - reg_usbh1_vbus: regulator-usbhubreset { - compatible = "regulator-fixed"; - regulator-name = "usbh1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbh1_hubreset>; - gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; - }; - reg_usb_otg_vbus: regulator-usbotgvbus { compatible = "regulator-fixed"; regulator-name = "usb_otg_vbus"; @@ -214,12 +202,18 @@ }; &usbh1 { - vbus-supply = <®_usbh1_vbus>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh1>; dr_mode = "host"; disable-over-current; status = "okay"; + + usb2415host: hub@1 { + compatible = "usb424,2513"; + reg = <1>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <3000>; + }; }; &usbotg { @@ -482,11 +476,6 @@ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0 /* usbh1_b OC */ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 - >; - }; - - pinctrl_usbh1_hubreset: usbh1hubresetgrp { - fsl,pins = < MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 >; }; diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi index d07d8f8..789fa55 100644 --- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi +++ b/arch/arm/boot/dts/imx6qdl-udoo.dtsi @@ -5,6 +5,8 @@ * Author: Fabio Estevam */ +#include + / { aliases { backlight = &backlight; @@ -62,17 +64,6 @@ #address-cells = <1>; #size-cells = <0>; - reg_usb_h1_vbus: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "usb_h1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */ - gpio = <&gpio7 12 0>; - }; - reg_panel: regulator@1 { compatible = "regulator-fixed"; reg = <1>; @@ -93,6 +84,17 @@ mux-int-port = <1>; mux-ext-port = <6>; }; + + udoo_ard: udoo_ard_manager { + compatible = "udoo,imx6q-udoo-ard"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_udooard>; + bossac-clk-gpio = <&gpio6 3 0>; + bossac-dat-gpio = <&gpio5 18 0>; + bossac-erase-gpio = <&gpio4 21 0>; + bossac-reset-gpio = <&gpio1 0 0>; + status = "okay"; + }; }; &fec { @@ -205,7 +207,7 @@ pinctrl_usbh: usbhgrp { fsl,pins = < - MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0 >; }; @@ -218,6 +220,15 @@ >; }; + pinctrl_udooard: udooardgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x80000000 + MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x80000000 + MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x80000000 + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x80000000 + >; + }; + pinctrl_usdhc3: usdhc3grp { fsl,pins = < MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 @@ -290,9 +301,16 @@ &usbh1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh>; - vbus-supply = <®_usb_h1_vbus>; - clocks = <&clks IMX6QDL_CLK_CKO>; status = "okay"; + + usb2415: hub@1 { + compatible = "usb424,2514"; + reg = <1>; + + clocks = <&clks IMX6QDL_CLK_CKO>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <3000>; + }; }; &usbotg { diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index 7a20265..262bdab 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -990,6 +990,8 @@ usbh1: usb@2184200 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184200 0x200>; interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; @@ -1004,6 +1006,8 @@ usbh2: usb@2184400 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184400 0x200>; interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; @@ -1019,6 +1023,8 @@ usbh3: usb@2184600 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184600 0x200>; interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; diff --git a/arch/arm/boot/dts/imx7d-pico-pi.dts b/arch/arm/boot/dts/imx7d-pico-pi.dts index 70bea95..a50edba 100644 --- a/arch/arm/boot/dts/imx7d-pico-pi.dts +++ b/arch/arm/boot/dts/imx7d-pico-pi.dts @@ -8,6 +8,10 @@ model = "TechNexion PICO-IMX7D Board and PI baseboard"; compatible = "technexion,imx7d-pico-pi", "fsl,imx7d"; + chosen { + stdout-path = "serial4:115200n8"; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index a858ebf..bc319ff 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -152,6 +152,7 @@ }; etb@5401b000 { + status = "disabled"; compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; @@ -167,6 +168,7 @@ }; etm@54010000 { + status = "disabled"; compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x54010000 0x1000>; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index f9f34b8..a1e9a89 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -139,6 +139,7 @@ }; etb@540000000 { + status = "disabled"; compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; @@ -154,6 +155,7 @@ }; etm@54010000 { + status = "disabled"; compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x54010000 0x1000>; diff --git a/arch/arm/boot/dts/omap4-panda-a4.dts b/arch/arm/boot/dts/omap4-panda-a4.dts index 8fd076e..92ed7ff 100644 --- a/arch/arm/boot/dts/omap4-panda-a4.dts +++ b/arch/arm/boot/dts/omap4-panda-a4.dts @@ -7,6 +7,18 @@ #include "omap443x.dtsi" #include "omap4-panda-common.dtsi" +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "okay"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "okay"; +}; + /* Pandaboard Rev A4+ have external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 609a8de..15faa11 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -501,16 +501,6 @@ }; }; -&emif1 { - cs1-used; - device-handle = <&elpida_ECB240ABACN>; -}; - -&emif2 { - cs1-used; - device-handle = <&elpida_ECB240ABACN>; -}; - &mcbsp1 { pinctrl-names = "default"; pinctrl-0 = <&mcbsp1_pins>; diff --git b/arch/arm/boot/dts/omap4-panda-es-b3.dts b/arch/arm/boot/dts/omap4-panda-es-b3.dts new file mode 100644 index 0000000..7c6886c --- /dev/null +++ b/arch/arm/boot/dts/omap4-panda-es-b3.dts @@ -0,0 +1,114 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ + */ +/dts-v1/; + +#include "omap4460.dtsi" +#include "omap4-panda-common.dtsi" + +/ { + model = "TI OMAP4 PandaBoard-ES"; + compatible = "ti,omap4-panda-es", "ti,omap4-panda", "ti,omap4460", "ti,omap4430", "ti,omap4"; +}; + +/* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ +&sound { + ti,model = "PandaBoardES"; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "AFML", "Line In", + "AFMR", "Line In"; +}; + +/* PandaboardES has external pullups on SCL & SDA */ +&dss_hdmi_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + >; +}; + +&omap4_pmx_core { + led_gpio_pins: gpio_led_pmx { + pinctrl-single,pins = < + OMAP4_IOPAD(0x0f6, PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x0fc, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_113 */ + >; + }; + + bt_pins: pinmux_bt_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 - BTEN */ + OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 - BTWAKEUP */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts - HCI */ + OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ + OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */ + OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + >; + }; +}; + +&led_wkgpio_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + >; +}; + +&leds { + pinctrl-0 = < + &led_gpio_pins + &led_wkgpio_pins + >; + + heartbeat { + gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; + }; + mmc { + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; +}; + +&gpio_keys { + buttonS2 { + gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* gpio_113 */ + }; +}; + +&gpio1_target { + ti,no-reset-on-init; +}; + +&wl12xx_gpio { + pinctrl-single,pins = < + OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */ + OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */ + >; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins &bt_pins>; + bluetooth: tiwi { + compatible = "ti,wl1271-st"; + enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>; /* GPIO_46 */ + }; +}; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index 7c6886c..878509a 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -12,6 +12,18 @@ compatible = "ti,omap4-panda-es", "ti,omap4-panda", "ti,omap4460", "ti,omap4430", "ti,omap4"; }; +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "okay"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "okay"; +}; + /* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ &sound { ti,model = "PandaBoardES"; diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts index 529d5bc..f362e6b 100644 --- a/arch/arm/boot/dts/omap4-panda.dts +++ b/arch/arm/boot/dts/omap4-panda.dts @@ -11,3 +11,15 @@ model = "TI OMAP4 PandaBoard"; compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4"; }; + +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "okay"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 9e97614..01314cc 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -523,11 +523,13 @@ &emif1 { cs1-used; device-handle = <&elpida_ECB240ABACN>; + status = "okay"; }; &emif2 { cs1-used; device-handle = <&elpida_ECB240ABACN>; + status = "okay"; }; &keypad { diff --git b/arch/arm/boot/dts/overlays/BBORG_FAN-A000.dts b/arch/arm/boot/dts/overlays/BBORG_FAN-A000.dts new file mode 100644 index 0000000..1b46782 --- /dev/null +++ b/arch/arm/boot/dts/overlays/BBORG_FAN-A000.dts @@ -0,0 +1,29 @@ +/* + * Copyright (C) 2020 Robert Nelson + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +/plugin/; + +/* +* Helper to show loaded overlays under: /proc/device-tree/chosen/overlays/ +*/ +&{/chosen} { + overlays { + BBORG_FAN-A000 = __TIMESTAMP__; + }; +}; + +&cpu0_opp_table { + opp_slow-400000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1060000 850000 1150000>, + <1060000 850000 1150000>; + opp-supported-hw = <0xFF 0x01>; + opp-suspend; + }; +}; diff --git b/arch/arm/boot/dts/overlays/Makefile b/arch/arm/boot/dts/overlays/Makefile new file mode 100644 index 0000000..522af05 --- /dev/null +++ b/arch/arm/boot/dts/overlays/Makefile @@ -0,0 +1,10 @@ +# Overlays for the BeagleBone platform + +dtbo-$(CONFIG_ARCH_OMAP2PLUS) += \ + BBORG_FAN-A000.dtbo + +targets += dtbs dtbs_install +targets += $(dtbo-y) + +always-y := $(dtbo-y) +clean-files := *.dtbo diff --git a/arch/arm/boot/dts/tps65217.dtsi b/arch/arm/boot/dts/tps65217.dtsi index 0d463de..a0717d9 100644 --- a/arch/arm/boot/dts/tps65217.dtsi +++ b/arch/arm/boot/dts/tps65217.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-only /* - * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ */ /* diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi index 93e07c1..a5d9c57 100644 --- a/arch/arm/boot/dts/twl4030.dtsi +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-only /* - * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/ */ /* diff --git a/arch/arm/boot/dts/twl6030.dtsi b/arch/arm/boot/dts/twl6030.dtsi index 9d588cf..102d38a 100644 --- a/arch/arm/boot/dts/twl6030.dtsi +++ b/arch/arm/boot/dts/twl6030.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-only /* - * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/ */ /* @@ -80,6 +80,11 @@ regulator-always-on; }; + clk32kg: regulator-clk32kg { + compatible = "ti,twl6030-clk32kg"; + regulator-always-on; + }; + twl_usb_comparator: usb-comparator { compatible = "ti,twl6030-usb"; interrupts = <4>, <10>; diff --git a/drivers/Makefile b/drivers/Makefile index fd11b9a..5bd01e0 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -56,6 +56,9 @@ obj-$(CONFIG_RESET_CONTROLLER) += reset/ obj-y += tty/ obj-y += char/ +# put mmc early as many morden devices use emm/sd card as rootfs storage +obj-y += mmc/ + # iommu/ comes before gpu as gpu are using iommu controllers obj-y += iommu/ @@ -128,7 +131,6 @@ obj-$(CONFIG_EISA) += eisa/ obj-$(CONFIG_PM_OPP) += opp/ obj-$(CONFIG_CPU_FREQ) += cpufreq/ obj-$(CONFIG_CPU_IDLE) += cpuidle/ -obj-y += mmc/ obj-$(CONFIG_MEMSTICK) += memstick/ obj-$(CONFIG_NEW_LEDS) += leds/ obj-$(CONFIG_INFINIBAND) += infiniband/ diff --git a/drivers/gnss/serial.c b/drivers/gnss/serial.c index def64b3..473faee 100644 --- a/drivers/gnss/serial.c +++ b/drivers/gnss/serial.c @@ -110,10 +110,9 @@ static int gnss_serial_set_power(struct gnss_serial *gserial, static int gnss_serial_parse_dt(struct serdev_device *serdev) { struct gnss_serial *gserial = serdev_device_get_drvdata(serdev); - struct device_node *node = serdev->dev.of_node; u32 speed = 4800; - of_property_read_u32(node, "current-speed", &speed); + device_property_read_u32(&serdev->dev, "current-speed", &speed); gserial->speed = speed; diff --git a/drivers/gnss/ubx.c b/drivers/gnss/ubx.c index 7b05bc4..e50056c 100644 --- a/drivers/gnss/ubx.c +++ b/drivers/gnss/ubx.c @@ -138,6 +138,14 @@ static const struct of_device_id ubx_of_match[] = { MODULE_DEVICE_TABLE(of, ubx_of_match); #endif +static const struct serdev_device_id ubx_serdev_id[] = { + { "neo-6m", }, + { "neo-8", }, + { "neo-m8", }, + {} +}; +MODULE_DEVICE_TABLE(serdev, ubx_serdev_id); + static struct serdev_device_driver ubx_driver = { .driver = { .name = "gnss-ubx", @@ -146,6 +154,7 @@ static struct serdev_device_driver ubx_driver = { }, .probe = ubx_probe, .remove = ubx_remove, + .id_table = ubx_serdev_id, }; module_serdev_device_driver(ubx_driver); diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index fa22517..c96cb38 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -95,6 +95,20 @@ config GPIO_CDEV_V1 If unsure, say Y. +config GPIO_OF_HELPER + bool "GPIO OF helper device (EXPERIMENTAL)" + depends on OF_GPIO + help + Say Y here to add an GPIO OF helper driver + + Allows you specify a GPIO helper based on OF + which allows simple export of GPIO functionality + in user-space. + + Features include, value set/get, direction control, + interrupt/value change poll support, event counting + and others. + config GPIO_GENERIC depends on HAS_IOMEM # Only for IOMEM drivers tristate diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 35e3b60..26f6704 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_OF_GPIO) += gpiolib-of.o obj-$(CONFIG_GPIO_CDEV) += gpiolib-cdev.o obj-$(CONFIG_GPIO_SYSFS) += gpiolib-sysfs.o obj-$(CONFIG_GPIO_ACPI) += gpiolib-acpi.o +obj-$(CONFIG_GPIO_OF_HELPER) += gpio-of-helper.o # Device drivers. Generally keep list sorted alphabetically obj-$(CONFIG_GPIO_REGMAP) += gpio-regmap.o diff --git b/drivers/gpio/gpio-of-helper.c b/drivers/gpio/gpio-of-helper.c new file mode 100644 index 0000000..83f362f --- /dev/null +++ b/drivers/gpio/gpio-of-helper.c @@ -0,0 +1,435 @@ +/* + * GPIO OF based helper + * + * A simple DT based driver to provide access to GPIO functionality + * to user-space via sysfs. + * + * Copyright (C) 2013 Pantelis Antoniou + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* fwd decl. */ +struct gpio_of_helper_info; + +enum gpio_type { + GPIO_TYPE_INPUT = 0, + GPIO_TYPE_OUTPUT = 1, +}; + +struct gpio_of_entry { + int id; + struct gpio_of_helper_info *info; + struct device_node *node; + enum gpio_type type; + int gpio; + int irq; + const char *name; + atomic64_t counter; + unsigned int count_flags; +#define COUNT_RISING_EDGE (1 << 0) +#define COUNT_FALLING_EDGE (1 << 1) +}; + +struct gpio_of_helper_info { + struct platform_device *pdev; + struct idr idr; +}; + +static const struct of_device_id gpio_of_helper_of_match[] = { + { + .compatible = "gpio-of-helper", + }, + { }, +}; +MODULE_DEVICE_TABLE(of, gpio_of_helper_of_match); + +static ssize_t gpio_of_helper_show_status(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct platform_device *pdev = to_platform_device(dev); + struct gpio_of_helper_info *info = platform_get_drvdata(pdev); + struct gpio_of_entry *entry; + char *p, *e; + int id, n; + + p = buf; + e = p + PAGE_SIZE; + n = 0; + idr_for_each_entry(&info->idr, entry, id) { + switch (entry->type) { + case GPIO_TYPE_INPUT: + n = snprintf(p, e - p, "%2d %-24s %3d %-3s %llu\n", + entry->id, entry->name, entry->gpio, "IN", + (unsigned long long) + atomic64_read(&entry->counter)); + break; + case GPIO_TYPE_OUTPUT: + n = snprintf(p, e - p, "%2d %-24s %3d %-3s\n", + entry->id, entry->name, entry->gpio, "OUT"); + break; + } + p += n; + } + + return p - buf; +} + +static DEVICE_ATTR(status, S_IRUGO, + gpio_of_helper_show_status, NULL); + +static irqreturn_t gpio_of_helper_handler(int irq, void *ptr) +{ + struct gpio_of_entry *entry = ptr; + + /* caution - low speed interfaces only! */ + atomic64_inc(&entry->counter); + + return IRQ_HANDLED; +} + +static struct gpio_of_entry * +gpio_of_entry_create(struct gpio_of_helper_info *info, + struct device_node *node) +{ + struct platform_device *pdev = info->pdev; + struct device *dev = &pdev->dev; + struct gpio_of_entry *entry; + int err, gpio, irq; + unsigned int req_flags, count_flags, irq_flags; + enum gpio_type type; + enum of_gpio_flags gpio_flags; + const char *name; + + /* get the type of the node first */ + if (of_property_read_bool(node, "input")) + type = GPIO_TYPE_INPUT; + else if (of_property_read_bool(node, "output") + || of_property_read_bool(node, "init-low") + || of_property_read_bool(node, "init-high")) + type = GPIO_TYPE_OUTPUT; + else { + dev_err(dev, "Not valid gpio node type\n"); + err = -EINVAL; + goto err_bad_node; + } + + /* get the name */ + if (of_property_read_string(node, "line-name", &name)) + if (of_property_read_string(node, "gpio-name", &name)) + name = node->name; + + err = of_get_named_gpio_flags(node, "gpio", 0, &gpio_flags); + if (IS_ERR_VALUE(err)) { + dev_err(dev, "Failed to get gpio property of '%s'\n", name); + goto err_bad_node; + } + gpio = err; + + req_flags = 0; + count_flags = 0; + + /* set the request flags */ + switch (type) { + case GPIO_TYPE_INPUT: + req_flags = GPIOF_DIR_IN | GPIOF_EXPORT; + if (of_property_read_bool(node, "count-falling-edge")) + count_flags |= COUNT_FALLING_EDGE; + if (of_property_read_bool(node, "count-rising-edge")) + count_flags |= COUNT_RISING_EDGE; + break; + case GPIO_TYPE_OUTPUT: + req_flags = GPIOF_DIR_OUT | GPIOF_EXPORT; + if (of_property_read_bool(node, "init-high")) + req_flags |= GPIOF_OUT_INIT_HIGH; + else if (of_property_read_bool(node, "init-low")) + req_flags |= GPIOF_OUT_INIT_LOW; + break; + } + if (of_property_read_bool(node, "dir-changeable")) + req_flags |= GPIOF_EXPORT_CHANGEABLE; + if (gpio_flags & OF_GPIO_ACTIVE_LOW) + req_flags |= GPIOF_ACTIVE_LOW; + if (gpio_flags & OF_GPIO_SINGLE_ENDED) { + if (gpio_flags & OF_GPIO_ACTIVE_LOW) + req_flags |= GPIOF_OPEN_DRAIN; + else + req_flags |= GPIOF_OPEN_SOURCE; + } + + /* request the gpio */ + err = devm_gpio_request_one(dev, gpio, req_flags, name); + if (err != 0) { + dev_err(dev, "Failed to request gpio '%s'\n", name); + goto err_bad_node; + } + + irq = -1; + irq_flags = 0; + + /* counter mode requested - need an interrupt */ + if (count_flags != 0) { + irq = gpio_to_irq(gpio); + if (IS_ERR_VALUE(irq)) { + dev_err(dev, "Failed to request gpio '%s'\n", name); + goto err_bad_node; + } + + if (count_flags & COUNT_RISING_EDGE) + irq_flags |= IRQF_TRIGGER_RISING; + if (count_flags & COUNT_FALLING_EDGE) + irq_flags |= IRQF_TRIGGER_FALLING; + } + +// if (!idr_pre_get(&info->idr, GFP_KERNEL)) { +// dev_err(dev, "Failed on idr_pre_get of '%s'\n", name); +// err = -ENOMEM; +// goto err_no_mem; +// } + + idr_preload(GFP_KERNEL); + + entry = devm_kzalloc(dev, sizeof(*entry), GFP_KERNEL); + if (entry == NULL) { + dev_err(dev, "Failed to allocate gpio entry of '%s'\n", name); + err = -ENOMEM; + goto err_no_mem; + } + + entry->id = -1; + entry->info = info; + entry->node = of_node_get(node); /* get node reference */ + entry->type = type; + entry->gpio = gpio; + entry->irq = irq; + entry->name = name; + + /* interrupt enable is last thing done */ + if (irq >= 0) { + atomic64_set(&entry->counter, 0); + entry->count_flags = count_flags; + err = devm_request_irq(dev, irq, gpio_of_helper_handler, + irq_flags, name, entry); + if (err != 0) { + dev_err(dev, "Failed to request irq of '%s'\n", name); + goto err_no_irq; + } + } + + /* all done; insert */ +// err = idr_get_new(&info->idr, entry, &entry->id); +// if (IS_ERR_VALUE(err)) { +// dev_err(dev, "Failed to idr_get_new of '%s'\n", name); +// goto err_fail_idr; +// } + + err = idr_alloc(&info->idr, entry, 0, 0, GFP_NOWAIT); + if (err >= 0) + entry->id = err; + + idr_preload_end(); + + if (err < 0) { + dev_err(dev, "Failed to idr_get_new of '%s'\n", name); + goto err_fail_idr; + } + + dev_dbg(dev, "Allocated GPIO id=%d name='%s'\n", entry->id, name); + + return entry; + +err_fail_idr: + /* nothing to do */ +err_no_irq: + /* release node ref */ + of_node_put(node); + /* nothing else needs to be done, devres handles it */ +err_no_mem: +err_bad_node: + return ERR_PTR(err); +} + +static int gpio_of_entry_destroy(struct gpio_of_entry *entry) +{ + struct gpio_of_helper_info *info = entry->info; + struct platform_device *pdev = info->pdev; + struct device *dev = &pdev->dev; + + dev_dbg(dev, "Destroying GPIO id=%d\n", entry->id); + + /* remove from the IDR */ + idr_remove(&info->idr, entry->id); + + /* remove node ref */ + of_node_put(entry->node); + + /* free gpio */ + devm_gpio_free(dev, entry->gpio); + + /* gree irq */ + if (entry->irq >= 0) + devm_free_irq(dev, entry->irq, entry); + + /* and free */ + devm_kfree(dev, entry); + + return 0; +} + +static int gpio_of_helper_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct gpio_of_helper_info *info; + struct gpio_of_entry *entry; + struct device_node *pnode = pdev->dev.of_node; + struct device_node *cnode; + struct pinctrl *pinctrl; + int err; + + /* we only support OF */ + if (pnode == NULL) { + dev_err(&pdev->dev, "No platform of_node!\n"); + return -ENODEV; + } + + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (IS_ERR(pinctrl)) { + /* special handling for probe defer */ + if (PTR_ERR(pinctrl) == -EPROBE_DEFER) + return -EPROBE_DEFER; + + dev_warn(&pdev->dev, + "pins are not configured from the driver\n"); + } + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (info == NULL) { + dev_err(&pdev->dev, "Failed to allocate info\n"); + err = -ENOMEM; + goto err_no_mem; + } + platform_set_drvdata(pdev, info); + info->pdev = pdev; + + idr_init(&info->idr); + + err = device_create_file(dev, &dev_attr_status); + if (err != 0) { + dev_err(dev, "Failed to create status sysfs attribute\n"); + goto err_no_sysfs; + } + + for_each_child_of_node(pnode, cnode) { + + entry = gpio_of_entry_create(info, cnode); + if (IS_ERR_OR_NULL(entry)) { + dev_err(dev, "Failed to create gpio entry\n"); + err = PTR_ERR(entry); + goto err_fail_entry; + } + } + + dev_info(&pdev->dev, "ready\n"); + + return 0; +err_fail_entry: + device_remove_file(&pdev->dev, &dev_attr_status); +err_no_sysfs: +err_no_mem: + return err; +} + +static int gpio_of_helper_remove(struct platform_device *pdev) +{ + struct gpio_of_helper_info *info = platform_get_drvdata(pdev); + struct gpio_of_entry *entry; + int id; + + dev_info(&pdev->dev, "removing\n"); + + device_remove_file(&pdev->dev, &dev_attr_status); + + id = 0; + idr_for_each_entry(&info->idr, entry, id) { + /* destroy each and every one */ + gpio_of_entry_destroy(entry); + } + + return 0; +} + +#ifdef CONFIG_PM +//#ifdef CONFIG_PM_RUNTIME +static int gpio_of_helper_runtime_suspend(struct device *dev) +{ + /* place holder */ + return 0; +} + +static int gpio_of_helper_runtime_resume(struct device *dev) +{ + /* place holder */ + return 0; +} +//#endif /* CONFIG_PM_RUNTIME */ + +static struct dev_pm_ops gpio_of_helper_pm_ops = { + SET_RUNTIME_PM_OPS(gpio_of_helper_runtime_suspend, + gpio_of_helper_runtime_resume, NULL) +}; +#define GPIO_OF_HELPER_PM_OPS (&gpio_of_helper_pm_ops) +#else +#define GPIO_OF_HELPER_PM_OPS NULL +#endif /* CONFIG_PM */ + +struct platform_driver gpio_of_helper_driver = { + .probe = gpio_of_helper_probe, + .remove = gpio_of_helper_remove, + .driver = { + .name = "gpio-of-helper", + .owner = THIS_MODULE, + .pm = GPIO_OF_HELPER_PM_OPS, + .of_match_table = gpio_of_helper_of_match, + }, +}; + +module_platform_driver(gpio_of_helper_driver); + +MODULE_AUTHOR("Pantelis Antoniou "); +MODULE_DESCRIPTION("GPIO OF Helper driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:gpio-of-helper"); diff --git a/drivers/gpio/gpiolib-sysfs.c b/drivers/gpio/gpiolib-sysfs.c index 26c5466..cc2adcf 100644 --- a/drivers/gpio/gpiolib-sysfs.c +++ b/drivers/gpio/gpiolib-sysfs.c @@ -38,10 +38,10 @@ static DEFINE_MUTEX(sysfs_lock); /* * /sys/class/gpio/gpioN... only for GPIOs that are exported * /direction - * * MAY BE OMITTED if kernel won't allow direction changes * * is read/write as "in" or "out" * * may also be written as "high" or "low", initializing * output value as specified ("out" implies "low") + * * read-only if kernel won't allow direction changes * /value * * always readable, subject to hardware behavior * * may be writable, as zero/nonzero @@ -54,6 +54,8 @@ static DEFINE_MUTEX(sysfs_lock); * * is read/write as zero/nonzero * * also affects existing and subsequent "falling" and "rising" * /edge configuration + * /label + * * descriptor label */ static ssize_t direction_show(struct device *dev, @@ -84,7 +86,9 @@ static ssize_t direction_store(struct device *dev, mutex_lock(&data->mutex); - if (sysfs_streq(buf, "high")) + if (!data->direction_can_change) + status = -EPERM; + else if (sysfs_streq(buf, "high")) status = gpiod_direction_output_raw(desc, 1); else if (sysfs_streq(buf, "out") || sysfs_streq(buf, "low")) status = gpiod_direction_output_raw(desc, 0); @@ -363,6 +367,23 @@ static ssize_t active_low_store(struct device *dev, } static DEVICE_ATTR_RW(active_low); +static ssize_t label_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; + ssize_t status; + + mutex_lock(&data->mutex); + + status = sprintf(buf, "%s\n", desc->label); + + mutex_unlock(&data->mutex); + + return status; +} +static DEVICE_ATTR_RO(label); + static umode_t gpio_is_visible(struct kobject *kobj, struct attribute *attr, int n) { @@ -374,12 +395,15 @@ static umode_t gpio_is_visible(struct kobject *kobj, struct attribute *attr, if (attr == &dev_attr_direction.attr) { if (!show_direction) - mode = 0; + mode &= 0444; } else if (attr == &dev_attr_edge.attr) { if (gpiod_to_irq(desc) < 0) mode = 0; if (!show_direction && test_bit(FLAG_IS_OUT, &desc->flags)) mode = 0; + } else if (attr == &dev_attr_value.attr) { + if (!show_direction && !test_bit(FLAG_IS_OUT, &desc->flags)) + mode &= 0444; } return mode; @@ -390,6 +414,7 @@ static struct attribute *gpio_attrs[] = { &dev_attr_edge.attr, &dev_attr_value.attr, &dev_attr_active_low.attr, + &dev_attr_label.attr, NULL, }; @@ -403,6 +428,10 @@ static const struct attribute_group *gpio_groups[] = { NULL }; +/* bwlegh, a second device in the same file... get out of my namespace! */ +#define dev_attr_label dev_attr_chip_label +#define label_show chip_label_show + /* * /sys/class/gpio/gpiochipN/ * /base ... matching gpio_chip.base (N) diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c index 97eec8d..cc36171 100644 --- a/drivers/gpio/gpiolib.c +++ b/drivers/gpio/gpiolib.c @@ -1845,9 +1845,9 @@ static int gpiod_request_commit(struct gpio_desc *desc, const char *label) if (test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0) { desc_set_label(desc, label ? : "?"); - } else { - ret = -EBUSY; - goto out_free_unlock; + //} else { + //ret = -EBUSY; + //goto out_free_unlock; } if (gc->request) { diff --git a/drivers/input/misc/tps65218-pwrbutton.c b/drivers/input/misc/tps65218-pwrbutton.c index f011447..e0c6dea 100644 --- a/drivers/input/misc/tps65218-pwrbutton.c +++ b/drivers/input/misc/tps65218-pwrbutton.c @@ -36,7 +36,7 @@ struct tps6521x_data { static const struct tps6521x_data tps65217_data = { .reg_status = TPS65217_REG_STATUS, .pb_mask = TPS65217_STATUS_PB, - .name = "tps65217_pwrbutton", + .name = "tps65217_pwr_but", }; static const struct tps6521x_data tps65218_data = { diff --git a/drivers/input/touchscreen/ar1021_i2c.c b/drivers/input/touchscreen/ar1021_i2c.c index c0d5c24..740956f 100644 --- a/drivers/input/touchscreen/ar1021_i2c.c +++ b/drivers/input/touchscreen/ar1021_i2c.c @@ -17,6 +17,7 @@ #define AR1021_MAX_X 4095 #define AR1021_MAX_Y 4095 +#define AR1021_MAX_PRESSURE 255 #define AR1021_CMD 0x55 @@ -26,8 +27,29 @@ struct ar1021_i2c { struct i2c_client *client; struct input_dev *input; u8 data[AR1021_TOUCH_PKG_SIZE]; + bool invert_x; + bool invert_y; + bool swap_xy; }; +static bool ar1021_get_prop_u32(struct device *dev, + const char *property, + unsigned int default_value, + unsigned int *value) +{ + u32 val; + int error; + + error = device_property_read_u32(dev, property, &val); + if (error) { + *value = default_value; + return false; + } + + *value = val; + return true; +} + static irqreturn_t ar1021_i2c_irq(int irq, void *dev_id) { struct ar1021_i2c *ar1021 = dev_id; @@ -49,9 +71,22 @@ static irqreturn_t ar1021_i2c_irq(int irq, void *dev_id) x = ((data[2] & 0x1f) << 7) | (data[1] & 0x7f); y = ((data[4] & 0x1f) << 7) | (data[3] & 0x7f); - input_report_abs(input, ABS_X, x); - input_report_abs(input, ABS_Y, y); + if (ar1021->invert_x) + x = AR1021_MAX_X - x; + + if (ar1021->invert_y) + y = AR1021_MAX_Y - y; + + if (ar1021->swap_xy) { + input_report_abs(input, ABS_X, y); + input_report_abs(input, ABS_Y, x); + } else { + input_report_abs(input, ABS_X, x); + input_report_abs(input, ABS_Y, y); + } + input_report_key(input, BTN_TOUCH, button); + input_report_abs(input, ABS_PRESSURE, AR1021_MAX_PRESSURE); input_sync(input); out: @@ -93,6 +128,8 @@ static int ar1021_i2c_probe(struct i2c_client *client, struct ar1021_i2c *ar1021; struct input_dev *input; int error; + unsigned int offset_x, offset_y; + bool data_present; if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { dev_err(&client->dev, "i2c_check_functionality error\n"); @@ -116,10 +153,44 @@ static int ar1021_i2c_probe(struct i2c_client *client, input->open = ar1021_i2c_open; input->close = ar1021_i2c_close; + ar1021->invert_x = device_property_read_bool(&client->dev, "touchscreen-inverted-x"); + ar1021->invert_y = device_property_read_bool(&client->dev, "touchscreen-inverted-y"); + ar1021->swap_xy = device_property_read_bool(&client->dev, "touchscreen-swapped-x-y"); + + data_present = ar1021_get_prop_u32(&client->dev, + "touchscreen-offset-x", + 0, + &offset_x); + + if (data_present) + dev_info(&client->dev, "touchscreen-offset-x: %d\n", offset_x); + + data_present = ar1021_get_prop_u32(&client->dev, + "touchscreen-offset-y", + 0, + &offset_y); + + if (data_present) + dev_info(&client->dev, "touchscreen-offset-y: %d\n", offset_y); + __set_bit(INPUT_PROP_DIRECT, input->propbit); - input_set_capability(input, EV_KEY, BTN_TOUCH); - input_set_abs_params(input, ABS_X, 0, AR1021_MAX_X, 0, 0); - input_set_abs_params(input, ABS_Y, 0, AR1021_MAX_Y, 0, 0); + //input_set_capability(input, EV_KEY, BTN_TOUCH); + + input->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS); + input->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH); + + if(ar1021->swap_xy) + { + input_set_abs_params(input, ABS_X, 0, AR1021_MAX_Y, 0, 0); + input_set_abs_params(input, ABS_Y, 0, AR1021_MAX_X, 0, 0); + } + else + { + input_set_abs_params(input, ABS_X, offset_x, AR1021_MAX_X-offset_x, 0, 0); + input_set_abs_params(input, ABS_Y, offset_y, AR1021_MAX_Y-offset_y, 0, 0); + } + + input_set_abs_params(input, ABS_PRESSURE, 0, AR1021_MAX_PRESSURE, 0, 0); input_set_drvdata(input, ar1021); diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c index 83e6855..dd358bf 100644 --- a/drivers/input/touchscreen/ti_am335x_tsc.c +++ b/drivers/input/touchscreen/ti_am335x_tsc.c @@ -34,6 +34,7 @@ #define ADCFSM_STEPID 0x10 #define SEQ_SETTLE 275 #define MAX_12BIT ((1 << 12) - 1) +#define PRESSURE_MAX 1000 #define TSC_IRQENB_MASK (IRQENB_FIFO0THRES | IRQENB_EOS | IRQENB_HW_PEN) @@ -234,6 +235,7 @@ static void titsc_read_coordinates(struct titsc *ts_dev, for (i = 0; i < creads; i++) { xvals[i] = titsc_readl(ts_dev, REG_FIFO0); xvals[i] &= 0xfff; + pr_debug("i %d xval %d yval %d z1 %d z2 %d\n", i, xvals[i], yvals[i], *z1, *z2); } /* @@ -312,13 +314,13 @@ static irqreturn_t titsc_irq(int irq, void *dev) * Resistance(touch) = x plate resistance * * x postion/4096 * ((z2 / z1) - 1) */ - z = z1 - z2; + z = z2 - z1; z *= x; z *= ts_dev->x_plate_resistance; - z /= z2; + z /= z1; z = (z + 2047) >> 12; - - if (z <= MAX_12BIT) { + pr_debug("x %d y %d z1 %d z2 %d z %d\n", x, y, z1, z2, z); + if (z <= PRESSURE_MAX) { input_report_abs(input_dev, ABS_X, x); input_report_abs(input_dev, ABS_Y, y); input_report_abs(input_dev, ABS_PRESSURE, z); @@ -459,6 +461,7 @@ static int titsc_probe(struct platform_device *pdev) input_dev->name = "ti-tsc"; input_dev->dev.parent = &pdev->dev; + __set_bit(INPUT_PROP_DIRECT, input_dev->propbit); input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS); input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH); diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index fafa8b0..6df932c 100644 --- a/drivers/misc/Kconfig +++ b/drivers/misc/Kconfig @@ -466,6 +466,13 @@ config HISI_HIKEY_USB switching between the dual-role USB-C port and the USB-A host ports using only one USB controller. +config UDOO_ARD + tristate "UDOO-Arduino erase/reset Driver" + default y + help + This driver is used to erase and reset arduino board via command sent + over USB-to-SERIAL connection. + source "drivers/misc/c2port/Kconfig" source "drivers/misc/eeprom/Kconfig" source "drivers/misc/cb710/Kconfig" @@ -475,6 +482,7 @@ source "drivers/misc/altera-stapl/Kconfig" source "drivers/misc/mei/Kconfig" source "drivers/misc/vmw_vmci/Kconfig" source "drivers/misc/genwqe/Kconfig" +source "drivers/misc/cape/Kconfig" source "drivers/misc/echo/Kconfig" source "drivers/misc/cxl/Kconfig" source "drivers/misc/ocxl/Kconfig" diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index d23231e..497e0d3 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -47,8 +47,10 @@ obj-$(CONFIG_LATTICE_ECP3_CONFIG) += lattice-ecp3-config.o obj-$(CONFIG_SRAM) += sram.o obj-$(CONFIG_SRAM_EXEC) += sram-exec.o obj-$(CONFIG_GENWQE) += genwqe/ +obj-y += cape/ obj-$(CONFIG_ECHO) += echo/ obj-$(CONFIG_CXL_BASE) += cxl/ +obj-$(CONFIG_UDOO_ARD) += udoo_ard.o obj-$(CONFIG_PCI_ENDPOINT_TEST) += pci_endpoint_test.o obj-$(CONFIG_OCXL) += ocxl/ obj-y += cardreader/ diff --git b/drivers/misc/cape/Kconfig b/drivers/misc/cape/Kconfig new file mode 100644 index 0000000..a2ef85e --- /dev/null +++ b/drivers/misc/cape/Kconfig @@ -0,0 +1,5 @@ +# +# Capes +# + +source "drivers/misc/cape/beaglebone/Kconfig" diff --git b/drivers/misc/cape/Makefile b/drivers/misc/cape/Makefile new file mode 100644 index 0000000..7c4eb96 --- /dev/null +++ b/drivers/misc/cape/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for cape like devices +# + +obj-y += beaglebone/ diff --git b/drivers/misc/cape/beaglebone/Kconfig b/drivers/misc/cape/beaglebone/Kconfig new file mode 100644 index 0000000..eeb6782 --- /dev/null +++ b/drivers/misc/cape/beaglebone/Kconfig @@ -0,0 +1,10 @@ +# +# Beaglebone capes +# + +config BEAGLEBONE_PINMUX_HELPER + tristate "Beaglebone Pinmux Helper" + depends on ARCH_OMAP2PLUS && OF + default n + help + Say Y here to include support for the pinmux helper diff --git b/drivers/misc/cape/beaglebone/Makefile b/drivers/misc/cape/beaglebone/Makefile new file mode 100644 index 0000000..7f4617a --- /dev/null +++ b/drivers/misc/cape/beaglebone/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for beaglebone capes +# + +obj-$(CONFIG_BEAGLEBONE_PINMUX_HELPER) += bone-pinmux-helper.o diff --git b/drivers/misc/cape/beaglebone/bone-pinmux-helper.c b/drivers/misc/cape/beaglebone/bone-pinmux-helper.c new file mode 100644 index 0000000..57703d8 --- /dev/null +++ b/drivers/misc/cape/beaglebone/bone-pinmux-helper.c @@ -0,0 +1,242 @@ +/* + * Pinmux helper driver + * + * Copyright (C) 2013 Pantelis Antoniou + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +static const struct of_device_id bone_pinmux_helper_of_match[] = { + { + .compatible = "bone-pinmux-helper", + }, + { }, +}; +MODULE_DEVICE_TABLE(of, bone_pinmux_helper_of_match); + +struct pinmux_helper_data { + struct pinctrl *pinctrl; + char *selected_state_name; +}; + +static ssize_t pinmux_helper_show_state(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct platform_device *pdev = to_platform_device(dev); + struct pinmux_helper_data *data = platform_get_drvdata(pdev); + const char *name; + + name = data->selected_state_name; + if (name == NULL || strlen(name) == 0) + name = "none"; + return sprintf(buf, "%s\n", name); +} + +static ssize_t pinmux_helper_store_state(struct device *dev, + struct device_attribute *attr, const char *buf, size_t count) +{ + struct platform_device *pdev = to_platform_device(dev); + struct pinmux_helper_data *data = platform_get_drvdata(pdev); + struct pinctrl_state *state; + char *state_name; + char *s; + int err; + + /* duplicate (as a null terminated string) */ + state_name = kmalloc(count + 1, GFP_KERNEL); + if (state_name == NULL) + return -ENOMEM; + memcpy(state_name, buf, count); + state_name[count] = '\0'; + + /* and chop off newline */ + s = strchr(state_name, '\n'); + if (s != NULL) + *s = '\0'; + + /* try to select default state at first (if it exists) */ + state = pinctrl_lookup_state(data->pinctrl, state_name); + if (!IS_ERR(state)) { + err = pinctrl_select_state(data->pinctrl, state); + if (err != 0) + dev_err(dev, "Failed to select state %s\n", + state_name); + } else { + dev_err(dev, "Failed to find state %s\n", state_name); + err = PTR_ERR_OR_ZERO(state); + } + + if (err == 0) { + kfree(data->selected_state_name); + data->selected_state_name = state_name; + } + + return err ? err : count; +} + +static DEVICE_ATTR(state, S_IWUSR | S_IRUGO, + pinmux_helper_show_state, pinmux_helper_store_state); + +static struct attribute *pinmux_helper_attributes[] = { + &dev_attr_state.attr, + NULL +}; + +static const struct attribute_group pinmux_helper_attr_group = { + .attrs = pinmux_helper_attributes, +}; + +static int bone_pinmux_helper_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct pinmux_helper_data *data; + struct pinctrl_state *state; + char *state_name; + const char *mode_name; + int mode_len; + int err; + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (data == NULL) { + dev_err(dev, "Failed to allocate data\n"); + err = -ENOMEM; + goto err_no_mem; + } + + state_name = kmalloc(strlen(PINCTRL_STATE_DEFAULT) + 1, + GFP_KERNEL); + if (state_name == NULL) { + dev_err(dev, "Failed to allocate state name\n"); + err = -ENOMEM; + goto err_no_state_mem; + } + data->selected_state_name = state_name; + strcpy(data->selected_state_name, PINCTRL_STATE_DEFAULT); + + platform_set_drvdata(pdev, data); + + data->pinctrl = devm_pinctrl_get(dev); + if (IS_ERR(data->pinctrl)) { + dev_err(dev, "Failed to get pinctrl\n"); + err = PTR_ERR_OR_ZERO(data->pinctrl); + goto err_no_pinctrl; + } + + /* See if an initial mode is specified in the device tree */ + mode_name = of_get_property(dev->of_node, "mode", &mode_len); + + err = -1; + if (mode_name != NULL ) { + state_name = kmalloc(mode_len + 1, GFP_KERNEL); + if (state_name == NULL) { + dev_err(dev, "Failed to allocate state name\n"); + err = -ENOMEM; + goto err_no_mode_mem; + } + strncpy(state_name, mode_name, mode_len); + + /* try to select requested mode */ + state = pinctrl_lookup_state(data->pinctrl, state_name); + if (!IS_ERR(state)) { + err = pinctrl_select_state(data->pinctrl, state); + if (err != 0) { + dev_warn(dev, "Unable to select requested mode %s\n", state_name); + kfree(state_name); + } else { + kfree(data->selected_state_name); + data->selected_state_name = state_name; + dev_notice(dev, "Set initial pinmux mode to %s\n", state_name); + } + } + } + + /* try to select default state if mode_name failed */ + if ( err != 0) { + state = pinctrl_lookup_state(data->pinctrl, + data->selected_state_name); + if (!IS_ERR(state)) { + err = pinctrl_select_state(data->pinctrl, state); + if (err != 0) { + dev_err(dev, "Failed to select default state\n"); + goto err_no_state; + } + } else { + data->selected_state_name = '\0'; + } + } + + /* Register sysfs hooks */ + err = sysfs_create_group(&dev->kobj, &pinmux_helper_attr_group); + if (err) { + dev_err(dev, "Failed to create sysfs group\n"); + goto err_no_sysfs; + } + + return 0; + +err_no_sysfs: +err_no_state: +err_no_mode_mem: + devm_pinctrl_put(data->pinctrl); +err_no_pinctrl: + devm_kfree(dev, data->selected_state_name); +err_no_state_mem: + devm_kfree(dev, data); +err_no_mem: + return err; +} + +static int bone_pinmux_helper_remove(struct platform_device *pdev) +{ + struct pinmux_helper_data *data = platform_get_drvdata(pdev); + struct device *dev = &pdev->dev; + + sysfs_remove_group(&dev->kobj, &pinmux_helper_attr_group); + kfree(data->selected_state_name); + devm_pinctrl_put(data->pinctrl); + devm_kfree(dev, data); + + return 0; +} + +struct platform_driver bone_pinmux_helper_driver = { + .probe = bone_pinmux_helper_probe, + .remove = bone_pinmux_helper_remove, + .driver = { + .name = "bone-pinmux-helper", + .owner = THIS_MODULE, + .of_match_table = bone_pinmux_helper_of_match, + }, +}; + +module_platform_driver(bone_pinmux_helper_driver); + +MODULE_AUTHOR("Pantelis Antoniou"); +MODULE_DESCRIPTION("Beaglebone pinmux helper driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:bone-pinmux-helper"); diff --git b/drivers/misc/udoo_ard.c b/drivers/misc/udoo_ard.c new file mode 100755 index 0000000..2210738 --- /dev/null +++ b/drivers/misc/udoo_ard.c @@ -0,0 +1,417 @@ +/* + * udoo_ard.c + * UDOO quad/dual Arduino flash erase / CPU resetter + * + * Copyright (C) 2013-2015 Aidilab srl + * Author: UDOO Team + * Author: Giuseppe Pagano + * Author: Francesco Montefoschi + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see . + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRIVER_NAME "udoo_ard" +#define PINCTRL_DEFAULT "default" +#define AUTH_TOKEN 0x5A5A +#define MAX_MSEC_SINCE_LAST_IRQ 400 +#define GRAY_TIME_BETWEEN_RESET 10000 // In this time we can't accept new erase/reset code + +static struct workqueue_struct *erase_reset_wq; +typedef struct { + struct work_struct erase_reset_work; + struct pinctrl *pinctrl; + struct pinctrl_state *pins_default; + int step; + int cmdcode; + int erase_reset_lock; + int gpio_bossac_clk; + int gpio_bossac_dat; + int gpio_ard_erase; + int gpio_ard_reset; + unsigned long last_int_time_in_ns; + unsigned long last_int_time_in_sec; +} erase_reset_work_t; + +erase_reset_work_t *work; +static u32 origTX, origRX; // original UART4 TX/RX pad control registers +static int major; // for /dev/udoo_ard +static struct class *udoo_class; + +static struct platform_device_id udoo_ard_devtype[] = { + { + /* keep it for coldfire */ + .name = DRIVER_NAME, + .driver_data = 0, + }, { + /* sentinel */ + } +}; +MODULE_DEVICE_TABLE(platform, udoo_ard_devtype); + +static const struct of_device_id udoo_ard_dt_ids[] = { + { .compatible = "udoo,imx6q-udoo-ard", .data = &udoo_ard_devtype[0], }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, udoo_ard_dt_ids); + +static void disable_serial(void) +{ + u32 addrTX; + void __iomem *_addrTX; + + printk("[bossac] Disable UART4 serial port.\n"); + + addrTX = 0x20E01F8; + _addrTX = ioremap(addrTX, 8); + + origTX = __raw_readl(_addrTX); + origRX = __raw_readl(_addrTX + 0x4); + + __raw_writel(0x15, _addrTX); + __raw_writel(0x15, _addrTX + 0x4); + + iounmap(_addrTX); +} + +static void enable_serial(void) +{ + u32 addrTX; + void __iomem *_addrTX; + + printk("[bossac] Enable UART4 serial port.\n"); + + addrTX = 0x20E01F8; + _addrTX = ioremap(addrTX, 8); + + __raw_writel(origTX, _addrTX); + __raw_writel(origRX, _addrTX + 0x4); + + iounmap(_addrTX); +} + +static void erase_reset(void) +{ + printk("[bossac] UDOO ERASE and RESET on Sam3x started.\n"); + + gpio_direction_input(work->gpio_ard_erase); + gpio_set_value(work->gpio_ard_reset, 1); + msleep(1); + + gpio_direction_output(work->gpio_ard_erase, 1); + msleep(300); + gpio_direction_input(work->gpio_ard_erase); + + msleep(10); + gpio_set_value(work->gpio_ard_reset, 0); + + msleep(80); + gpio_set_value(work->gpio_ard_reset, 1); + + printk("[bossac] UDOO ERASE and RESET on Sam3x EXECUTED.\n"); +} + +static void shutdown_sam3x(void) +{ + printk("[bossac] RESET on Sam3x.\n"); + + gpio_set_value(work->gpio_ard_reset, 0); +} + +static void erase_reset_wq_function( struct work_struct *work2) +{ + disable_serial(); + erase_reset(); + msleep(GRAY_TIME_BETWEEN_RESET); + + work->erase_reset_lock = 0; +} + +/* + * Called everytime the gpio_bossac_clk signal toggles. + * If the auth token (16 bit) is found, we look for the command code (4 bit). + * The code 0x0F is sent by Bossac to trigger an erase/reset (to achieve this, + * erase_reset_wq is scheduled). Before starting to program the flash, we disable + * the UART4 serial port, otherwise there is too noise on the serial lines (the + * programming port and UART4 port are connected together, see hw schematics). + * When Bossac finishes to flash/verify, the code 0x00 is sent which re-enables + * the UART4 port. + */ +static irqreturn_t udoo_bossac_req(int irq, void *dev_id) +{ + int retval, auth_bit, expected_bit, msec_since_last_irq; + u64 nowsec; + unsigned long rem_nsec; + erase_reset_work_t *erase_reset_work; + + auth_bit = 0; + if (gpio_get_value(work->gpio_bossac_dat) != 0x0) { + auth_bit = 1; + } + + erase_reset_work = (erase_reset_work_t *)work; + + nowsec = local_clock(); + rem_nsec = do_div(nowsec, 1000000000) ; + msec_since_last_irq = (((unsigned long)nowsec * 1000) + rem_nsec/1000000 ) - (((unsigned long)erase_reset_work->last_int_time_in_sec * 1000) + erase_reset_work->last_int_time_in_ns/1000000); + + if (msec_since_last_irq > MAX_MSEC_SINCE_LAST_IRQ) { + erase_reset_work->step = 0; +#ifdef DEBUG + printk("[bossac] Reset authentication timeout!\n"); +#endif + } + +#ifdef DEBUG + printk("[bossac] STEP %d -> 0x%d \n", erase_reset_work->step, auth_bit); +#endif + erase_reset_work->last_int_time_in_ns = rem_nsec; + erase_reset_work->last_int_time_in_sec = nowsec; + + if ( erase_reset_work->step < 16 ) { // Authenticating received token bit. + expected_bit = (( AUTH_TOKEN >> erase_reset_work->step ) & 0x01 ); + if ( auth_bit == expected_bit ) { + erase_reset_work->step = erase_reset_work->step + 1; + } else { + erase_reset_work->step = 0; + } + } else { // Passed all authentication step. Receiving command code. + erase_reset_work->cmdcode = erase_reset_work->cmdcode | (auth_bit << (erase_reset_work->step - 16)); + erase_reset_work->step = erase_reset_work->step + 1; + } + +#ifdef DEBUG + printk("erase_reset_work->erase_reset_lock = %d \n", erase_reset_work->erase_reset_lock); +#endif + if ( erase_reset_work->step == 20 ) { // Passed authentication and code acquiring step. +#ifdef DEBUG + printk("[bossac] Received code = 0x%04x \n", erase_reset_work->cmdcode); +#endif + if (erase_reset_work->cmdcode == 0xF) { + if (erase_reset_work->erase_reset_lock == 0) { + erase_reset_work->erase_reset_lock = 1; + retval = queue_work( erase_reset_wq, (struct work_struct *)work ); + } else { +#ifdef DEBUG + printk("Erase and reset operation already in progress. Do nothing.\n"); +#endif + } + } else { + enable_serial(); + } + erase_reset_work->step = 0; + erase_reset_work->cmdcode = 0; + } + + return IRQ_HANDLED; +} + +/* + * Takes control of clock, data, erase, reset GPIOs. + */ +static int gpio_setup(void) +{ + int ret; + + ret = gpio_request(work->gpio_bossac_clk, "BOSSA_CLK"); + if (ret) { + printk(KERN_ERR "request BOSSA_CLK IRQ\n"); + return -1; + } else { + gpio_direction_input(work->gpio_bossac_clk); + } + + ret = gpio_request(work->gpio_bossac_dat, "BOSSA_DAT"); + if (ret) { + printk(KERN_ERR "request BOSSA_DAT IRQ\n"); + return -1; + } else { + gpio_direction_input(work->gpio_bossac_dat); + } + + ret = gpio_request(work->gpio_ard_erase, "BOSSAC"); + if (ret) { + printk(KERN_ERR "request GPIO FOR ARDUINO ERASE\n"); + return -1; + } else { + gpio_direction_input(work->gpio_ard_erase); + } + + ret = gpio_request(work->gpio_ard_reset, "BOSSAC"); + if (ret) { + printk(KERN_ERR "request GPIO FOR ARDUINO RESET\n"); + return -1; + } else { + gpio_direction_output(work->gpio_ard_reset, 1); + } + + return 0; +} + +static ssize_t device_write(struct file *filp, const char *buff, size_t len, loff_t *off) +{ + char msg[10]; + long res; + + if (len > 10) + return -EINVAL; + + + res = copy_from_user(msg, buff, len); + if (res) { + return -EFAULT; + } + msg[len] = '\0'; + + if (strcmp(msg, "erase")==0) { + erase_reset(); + } else if (strcmp(msg, "shutdown")==0) { + shutdown_sam3x(); + } else if (strcmp(msg, "uartoff")==0) { + disable_serial(); + } else if (strcmp(msg, "uarton")==0) { + enable_serial(); + } else { + printk("[bossac] udoo_ard invalid operation! %s", msg); + } + + return len; +} + +static struct file_operations fops = { + .write = device_write, +}; + +/* + * If a fdt udoo_ard entry is found, we register an IRQ on bossac clock line + * and we create /dev/udoo_ard + */ +static int udoo_ard_probe(struct platform_device *pdev) +{ + int retval; + struct device *temp_class; + struct platform_device *bdev; + struct device_node *np; + + bdev = kzalloc(sizeof(*bdev), GFP_KERNEL); + np = pdev->dev.of_node; + + if (!np) + return -ENODEV; + + work = (erase_reset_work_t *)kmalloc(sizeof(erase_reset_work_t), GFP_KERNEL); + if (work) { + work->gpio_ard_reset = of_get_named_gpio(np, "bossac-reset-gpio", 0); + work->gpio_ard_erase = of_get_named_gpio(np, "bossac-erase-gpio", 0); + work->gpio_bossac_clk = of_get_named_gpio(np, "bossac-clk-gpio", 0); + work->gpio_bossac_dat = of_get_named_gpio(np, "bossac-dat-gpio", 0); + work->pinctrl = devm_pinctrl_get(&pdev->dev); + work->pins_default = pinctrl_lookup_state(work->pinctrl, PINCTRL_DEFAULT); + } else { + printk("[bossac] Failed to allocate data structure."); + return -ENOMEM; + } + + pinctrl_select_state(work->pinctrl, work->pins_default); + gpio_setup(); + + printk("[bossac] Registering IRQ %d for BOSSAC Arduino erase/reset operation\n", gpio_to_irq(work->gpio_bossac_clk)); + retval = request_irq(gpio_to_irq(work->gpio_bossac_clk), udoo_bossac_req, IRQF_TRIGGER_FALLING, "UDOO", bdev); + + major = register_chrdev(major, "udoo_ard", &fops); + if (major < 0) { + printk(KERN_ERR "[bossac] Cannot get major for UDOO Ard\n"); + return -EBUSY; + } + + udoo_class = class_create(THIS_MODULE, "udoo_ard"); + if (IS_ERR(udoo_class)) { + return PTR_ERR(udoo_class); + } + + temp_class = device_create(udoo_class, NULL, MKDEV(major, 0), NULL, "udoo_ard"); + if (IS_ERR(temp_class)) { + return PTR_ERR(temp_class); + } + + printk("[bossac] Created device file /dev/udoo_ard\n"); + + erase_reset_wq = create_workqueue("erase_reset_queue"); + if (erase_reset_wq) { + + /* Queue some work (item 1) */ + if (work) { + INIT_WORK( (struct work_struct *)work, erase_reset_wq_function ); + work->step = 1; + work->cmdcode = 0; + work->last_int_time_in_ns = 0; + work->last_int_time_in_sec = 0; + work->erase_reset_lock = 0; + // retval = queue_work( erase_reset_wq, (struct work_struct *)work ); + } + } + return 0; +} + +static int udoo_ard_remove(struct platform_device *pdev) +{ + printk("[bossac] Unloading UDOO ard driver.\n"); + free_irq(gpio_to_irq(work->gpio_bossac_clk), NULL); + + gpio_free(work->gpio_ard_reset); + gpio_free(work->gpio_ard_erase); + gpio_free(work->gpio_bossac_clk); + gpio_free(work->gpio_bossac_dat); + + device_destroy(udoo_class, MKDEV(major, 0)); + class_destroy(udoo_class); + unregister_chrdev(major, "udoo_ard"); + + return 0; +} + +static struct platform_driver udoo_ard_driver = { + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + .of_match_table = udoo_ard_dt_ids, + }, + .id_table = udoo_ard_devtype, + .probe = udoo_ard_probe, + .remove = udoo_ard_remove, +}; + +module_platform_driver(udoo_ard_driver); + +MODULE_ALIAS("platform:"DRIVER_NAME); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c index cfff3d4..709152b 100644 --- a/drivers/net/ethernet/ti/davinci_mdio.c +++ b/drivers/net/ethernet/ti/davinci_mdio.c @@ -92,6 +92,10 @@ struct davinci_mdio_data { u32 clk_div; }; +#if IS_ENABLED(CONFIG_OF) +static void davinci_mdio_update_dt_from_phymask(u32 phy_mask); +#endif + static void davinci_mdio_init_clk(struct davinci_mdio_data *data) { u32 mdio_in, div, mdio_out_khz, access_time; @@ -159,6 +163,12 @@ static int davinci_mdio_reset(struct mii_bus *bus) /* restrict mdio bus to live phys only */ dev_info(data->dev, "detected phy mask %x\n", ~phy_mask); phy_mask = ~phy_mask; + + #if IS_ENABLED(CONFIG_OF) + if (of_machine_is_compatible("ti,am335x-bone")) + davinci_mdio_update_dt_from_phymask(phy_mask); + #endif + } else { /* desperately scan all phys */ dev_warn(data->dev, "no live phy, scanning all\n"); @@ -474,6 +484,93 @@ static int davinci_mdio_runtime_resume(struct device *dev) davinci_mdio_enable(data); return 0; } +static void davinci_mdio_update_dt_from_phymask(u32 phy_mask) +{ + int i, len, skip; + u32 addr; + __be32 *old_phy_p, *phy_id_p; + struct property *phy_id_property = NULL; + struct device_node *node_p, *slave_p; + + addr = 0; + + for (i = 0; i < PHY_MAX_ADDR; i++) { + if ((phy_mask & (1 << i)) == 0) { + addr = (u32) i; + break; + } + } + + for_each_compatible_node(node_p, NULL, "ti,cpsw") { + for_each_node_by_name(slave_p, "slave") { + +#if IS_ENABLED(CONFIG_OF_OVERLAY) + skip = 1; + // Hack, the overlay fixup "slave" doesn't have phy-mode... + old_phy_p = (__be32 *) of_get_property(slave_p, "phy-mode", &len); + + if (len != (sizeof(__be32 *) * 1)) + { + skip = 0; + } + + if (skip) { +#endif + + old_phy_p = (__be32 *) of_get_property(slave_p, "phy_id", &len); + + if (len != (sizeof(__be32 *) * 2)) + goto err_out; + + if (old_phy_p) { + + phy_id_property = kzalloc(sizeof(*phy_id_property), GFP_KERNEL); + + if (! phy_id_property) + goto err_out; + + phy_id_property->length = len; + phy_id_property->name = kstrdup("phy_id", GFP_KERNEL); + phy_id_property->value = kzalloc(len, GFP_KERNEL); + + if (! phy_id_property->name) + goto err_out; + + if (! phy_id_property->value) + goto err_out; + + memcpy(phy_id_property->value, old_phy_p, len); + + phy_id_p = (__be32 *) phy_id_property->value + 1; + + *phy_id_p = cpu_to_be32(addr); + + of_update_property(slave_p, phy_id_property); + pr_info("davinci_mdio: dt: updated phy_id[%d] from phy_mask[%x]\n", addr, phy_mask); + + ++addr; + } +#if IS_ENABLED(CONFIG_OF_OVERLAY) + } +#endif + } + } + + return; + +err_out: + + if (phy_id_property) { + if (phy_id_property->name) + kfree(phy_id_property->name); + + if (phy_id_property->value) + kfree(phy_id_property->value); + + if (phy_id_property) + kfree(phy_id_property); + } +} #endif #ifdef CONFIG_PM_SLEEP diff --git a/drivers/net/ieee802154/Kconfig b/drivers/net/ieee802154/Kconfig index 0f7c6dc..0a1d876 100644 --- a/drivers/net/ieee802154/Kconfig +++ b/drivers/net/ieee802154/Kconfig @@ -73,6 +73,15 @@ config IEEE802154_ATUSB This driver can also be built as a module. To do so say M here. The module will be called 'atusb'. +config IEEE802154_WPANUSB + tristate "WPANUSB driver" + depends on IEEE802154_DRIVERS && MAC802154 && USB + help + Adds support for WPANUSB 802.15.4 adapters. + + This driver should work with at least the following devices: + * BeagleBoard.org BeagleConnect Freedom + config IEEE802154_ADF7242 tristate "ADF7242 transceiver driver" depends on IEEE802154_DRIVERS && MAC802154 diff --git a/drivers/net/ieee802154/Makefile b/drivers/net/ieee802154/Makefile index 0c78b62..59442aa 100644 --- a/drivers/net/ieee802154/Makefile +++ b/drivers/net/ieee802154/Makefile @@ -4,6 +4,7 @@ obj-$(CONFIG_IEEE802154_AT86RF230) += at86rf230.o obj-$(CONFIG_IEEE802154_MRF24J40) += mrf24j40.o obj-$(CONFIG_IEEE802154_CC2520) += cc2520.o obj-$(CONFIG_IEEE802154_ATUSB) += atusb.o +obj-$(CONFIG_IEEE802154_WPANUSB) += wpanusb.o obj-$(CONFIG_IEEE802154_ADF7242) += adf7242.o obj-$(CONFIG_IEEE802154_CA8210) += ca8210.o obj-$(CONFIG_IEEE802154_MCR20A) += mcr20a.o diff --git b/drivers/net/ieee802154/wpanusb.c b/drivers/net/ieee802154/wpanusb.c new file mode 100644 index 0000000..698f2c5 --- /dev/null +++ b/drivers/net/ieee802154/wpanusb.c @@ -0,0 +1,757 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Driver for the WPANUSB IEEE 802.15.4 dongle + * + * Copyright (C) 2018 Intel Corp. + * + * The driver implements SoftMAC 802.15.4 protocol based on atusb + * driver for ATUSB IEEE 802.15.4 dongle. + * + * Written by Andrei Emeltchenko + */ + +#include +#include +#include +#include + +#include +#include + +#define DEBUG +#include "wpanusb.h" + +#define WPANUSB_NUM_RX_URBS 4 /* allow for a bit of local latency */ +#define WPANUSB_ALLOC_DELAY_MS 100 /* delay after failed allocation */ + +#define VENDOR_OUT (USB_TYPE_VENDOR | USB_DIR_OUT) + +#define WPANUSB_VALID_CHANNELS (0x07FFFFFF) + +struct wpanusb { + struct ieee802154_hw *hw; + struct usb_device *udev; + int shutdown; /* non-zero if shutting down */ + + /* RX variables */ + struct delayed_work work; /* memory allocations */ + struct usb_anchor idle_urbs; /* URBs waiting to be submitted */ + struct usb_anchor rx_urbs; /* URBs waiting for reception */ + + /* TX variables */ + struct usb_ctrlrequest tx_dr; + struct urb *tx_urb; + struct sk_buff *tx_skb; + u8 tx_ack_seq; /* current TX ACK sequence number */ +}; + +/* ----- USB commands without data ----------------------------------------- */ + +static int wpanusb_control_send(struct wpanusb *wpanusb, unsigned int pipe, + u8 request, void *data, u16 size) +{ + struct usb_device *udev = wpanusb->udev; + + return usb_control_msg(udev, pipe, request, VENDOR_OUT, + 0, 0, data, size, 1000); +} + +/* ----- skb allocation ---------------------------------------------------- */ + +#define MAX_PSDU 127 +#define MAX_RX_XFER (1 + MAX_PSDU + 2 + 1) /* PHR+PSDU+CRC+LQI */ + +#define SKB_WPANUSB(skb) (*(struct wpanusb **)(skb)->cb) + +static void wpanusb_bulk_complete(struct urb *urb); + +static int wpanusb_submit_rx_urb(struct wpanusb *wpanusb, struct urb *urb) +{ + struct usb_device *udev = wpanusb->udev; + struct sk_buff *skb = urb->context; + int ret; + + if (!skb) { + skb = alloc_skb(MAX_RX_XFER, GFP_KERNEL); + if (!skb) { + dev_warn_ratelimited(&udev->dev, + "can't allocate skb\n"); + return -ENOMEM; + } + skb_put(skb, MAX_RX_XFER); + SKB_WPANUSB(skb) = wpanusb; + } + + usb_fill_bulk_urb(urb, udev, usb_rcvbulkpipe(udev, 1), + skb->data, MAX_RX_XFER, wpanusb_bulk_complete, skb); + usb_anchor_urb(urb, &wpanusb->rx_urbs); + + ret = usb_submit_urb(urb, GFP_KERNEL); + if (ret) { + usb_unanchor_urb(urb); + kfree_skb(skb); + urb->context = NULL; + } + + return ret; +} + +static void wpanusb_work_urbs(struct work_struct *work) +{ + struct wpanusb *wpanusb = + container_of(to_delayed_work(work), struct wpanusb, work); + struct usb_device *udev = wpanusb->udev; + struct urb *urb; + int ret; + + if (wpanusb->shutdown) + return; + + do { + urb = usb_get_from_anchor(&wpanusb->idle_urbs); + if (!urb) + return; + + ret = wpanusb_submit_rx_urb(wpanusb, urb); + } while (!ret); + + usb_anchor_urb(urb, &wpanusb->idle_urbs); + dev_warn_ratelimited(&udev->dev, "can't allocate/submit URB (%d)\n", + ret); + schedule_delayed_work(&wpanusb->work, + msecs_to_jiffies(WPANUSB_ALLOC_DELAY_MS) + 1); +} + +/* ----- Asynchronous USB -------------------------------------------------- */ + +static void wpanusb_tx_done(struct wpanusb *wpanusb, uint8_t seq) +{ + struct usb_device *udev = wpanusb->udev; + u8 expect = wpanusb->tx_ack_seq; + + dev_dbg(&udev->dev, "seq 0x%02x expect 0x%02x\n", seq, expect); + + if (seq == expect) { + ieee802154_xmit_complete(wpanusb->hw, wpanusb->tx_skb, false); + } else { + dev_dbg(&udev->dev, "unknown ack %u\n", seq); + + ieee802154_wake_queue(wpanusb->hw); + if (wpanusb->tx_skb) + dev_kfree_skb_irq(wpanusb->tx_skb); + } +} + +static void wpanusb_process_urb(struct urb *urb) +{ + struct usb_device *udev = urb->dev; + struct sk_buff *skb = urb->context; + struct wpanusb *wpanusb = SKB_WPANUSB(skb); + u8 len, lqi; + + if (!urb->actual_length) { + dev_dbg(&udev->dev, "zero-sized URB ?\n"); + return; + } + + len = *skb->data; + + dev_dbg(&udev->dev, "urb %p urb len %u pkt len %u", urb, + urb->actual_length, len); + + /* Handle ACK */ + if (urb->actual_length == 1) { + wpanusb_tx_done(wpanusb, len); + return; + } + + if (len + 1 > urb->actual_length - 1) { + dev_dbg(&udev->dev, "frame len %d+1 > URB %u-1\n", + len, urb->actual_length); + return; + } + + if (!ieee802154_is_valid_psdu_len(len)) { + dev_dbg(&udev->dev, "frame corrupted\n"); + return; + } + + print_hex_dump_bytes("> ", DUMP_PREFIX_OFFSET, skb->data, + urb->actual_length); + + /* Get LQI at the end of the packet */ + lqi = skb->data[len + 1]; + dev_dbg(&udev->dev, "rx len %d lqi 0x%02x\n", len, lqi); + skb_pull(skb, 1); /* remove length */ + skb_trim(skb, len); /* remove LQI */ + ieee802154_rx_irqsafe(wpanusb->hw, skb, lqi); + urb->context = NULL; /* skb is gone */ +} + +static void wpanusb_bulk_complete(struct urb *urb) +{ + struct usb_device *udev = urb->dev; + struct sk_buff *skb = urb->context; + struct wpanusb *wpanusb = SKB_WPANUSB(skb); + + dev_dbg(&udev->dev, "status %d len %d\n", + urb->status, urb->actual_length); + + if (urb->status) { + if (urb->status == -ENOENT) { /* being killed */ + kfree_skb(skb); + urb->context = NULL; + return; + } + + dev_dbg(&udev->dev, "URB error %d\n", urb->status); + } else { + wpanusb_process_urb(urb); + } + + usb_anchor_urb(urb, &wpanusb->idle_urbs); + if (!wpanusb->shutdown) + schedule_delayed_work(&wpanusb->work, 0); +} + +/* ----- URB allocation/deallocation --------------------------------------- */ + +static void wpanusb_free_urbs(struct wpanusb *wpanusb) +{ + struct urb *urb; + + do { + urb = usb_get_from_anchor(&wpanusb->idle_urbs); + if (!urb) + break; + kfree_skb(urb->context); + usb_free_urb(urb); + } while (true); +} + +static int wpanusb_alloc_urbs(struct wpanusb *wpanusb, unsigned int n) +{ + struct urb *urb; + + while (n--) { + urb = usb_alloc_urb(0, GFP_KERNEL); + if (!urb) { + wpanusb_free_urbs(wpanusb); + return -ENOMEM; + } + usb_anchor_urb(urb, &wpanusb->idle_urbs); + } + + return 0; +} + +/* ----- IEEE 802.15.4 interface operations -------------------------------- */ + +static void wpanusb_xmit_complete(struct urb *urb) +{ + dev_dbg(&urb->dev->dev, "urb transmit completed"); +} + +static int wpanusb_xmit(struct ieee802154_hw *hw, struct sk_buff *skb) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + int ret = 0; + + dev_dbg(&udev->dev, "len %u", skb->len); + + /* ack_seq range is 0x01 - 0xff */ + wpanusb->tx_ack_seq++; + if (!wpanusb->tx_ack_seq) + wpanusb->tx_ack_seq++; + + wpanusb->tx_skb = skb; + wpanusb->tx_dr.wIndex = cpu_to_le16(wpanusb->tx_ack_seq); + wpanusb->tx_dr.wLength = cpu_to_le16(skb->len); + + usb_fill_control_urb(wpanusb->tx_urb, udev, + usb_sndctrlpipe(udev, 0), + (unsigned char *)&wpanusb->tx_dr, skb->data, + skb->len, wpanusb_xmit_complete, NULL); + ret = usb_submit_urb(wpanusb->tx_urb, GFP_ATOMIC); + + dev_dbg(&udev->dev, "%s: ret %d len %u seq %u\n", __func__, ret, + skb->len, wpanusb->tx_ack_seq); + + return ret; +} + +static int wpanusb_channel(struct ieee802154_hw *hw, u8 page, u8 channel) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + struct set_channel *req; + int ret; + + req = kmalloc(sizeof(*req), GFP_KERNEL); + if (!req) + return -ENOMEM; + + req->page = page; + req->channel = channel; + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + SET_CHANNEL, req, sizeof(*req)); + kfree(req); + if (ret < 0) { + dev_err(&udev->dev, "Failed set channel, ret %d", ret); + return ret; + } + + dev_dbg(&udev->dev, "set page %u channel %u", page, channel); + + return 0; +} + +static int wpanusb_ed(struct ieee802154_hw *hw, u8 *level) +{ + WARN_ON(!level); + + *level = 0xbe; + + return 0; +} + +static int wpanusb_set_hw_addr_filt(struct ieee802154_hw *hw, + struct ieee802154_hw_addr_filt *filt, + unsigned long changed) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + int ret = 0; + + if (changed & IEEE802154_AFILT_SADDR_CHANGED) { + struct set_short_addr *req; + + req = kmalloc(sizeof(*req), GFP_KERNEL); + if (!req) + return -ENOMEM; + + req->short_addr = filt->short_addr; + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + SET_SHORT_ADDR, req, sizeof(*req)); + kfree(req); + if (ret < 0) { + dev_err(&udev->dev, "Failed to set short_addr, ret %d", + ret); + return ret; + } + + dev_dbg(&udev->dev, "short addr changed to 0x%04x", + le16_to_cpu(filt->short_addr)); + } + + if (changed & IEEE802154_AFILT_PANID_CHANGED) { + struct set_pan_id *req; + + req = kmalloc(sizeof(*req), GFP_KERNEL); + if (!req) + return -ENOMEM; + + req->pan_id = filt->pan_id; + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + SET_PAN_ID, req, sizeof(*req)); + kfree(req); + if (ret < 0) { + dev_err(&udev->dev, "Failed to set pan_id, ret %d", + ret); + return ret; + } + + dev_dbg(&udev->dev, "pan id changed to 0x%04x", + le16_to_cpu(filt->pan_id)); + } + + if (changed & IEEE802154_AFILT_IEEEADDR_CHANGED) { + struct set_ieee_addr *req; + + req = kmalloc(sizeof(*req), GFP_KERNEL); + if (!req) + return -ENOMEM; + + memcpy(&req->ieee_addr, &filt->ieee_addr, + sizeof(req->ieee_addr)); + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + SET_IEEE_ADDR, req, sizeof(*req)); + kfree(req); + if (ret < 0) { + dev_err(&udev->dev, "Failed to set ieee_addr, ret %d", + ret); + return ret; + } + + dev_dbg(&udev->dev, "IEEE addr changed"); + } + + if (changed & IEEE802154_AFILT_PANC_CHANGED) { + dev_dbg(&udev->dev, "panc changed"); + + dev_err(&udev->dev, "Not handled AFILT_PANC_CHANGED"); + } + + return ret; +} + +static int wpanusb_set_extended_addr(struct ieee802154_hw *hw) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + unsigned char *buffer; + __le64 extended_addr; + int ret = 0; + u64 addr; + + buffer = kmalloc(IEEE802154_EXTENDED_ADDR_LEN, GFP_KERNEL); + if (!buffer) + return -ENOMEM; + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), GET_EXTENDED_ADDR, buffer, + IEEE802154_EXTENDED_ADDR_LEN); + if (ret < 0) { + dev_err(&udev->dev, "failed to fetch extended address, random address set\n"); + ieee802154_random_extended_addr(&wpanusb->hw->phy->perm_extended_addr); + kfree(buffer); + return ret; + } + + memcpy(&extended_addr, buffer, IEEE802154_EXTENDED_ADDR_LEN); + /* Check if read address is not empty and the unicast bit is set correctly */ + if (!ieee802154_is_valid_extended_unicast_addr(extended_addr)) { + dev_info(&udev->dev, "no permanent extended address found, random address set\n"); + ieee802154_random_extended_addr(&wpanusb->hw->phy->perm_extended_addr); + } else { + wpanusb->hw->phy->perm_extended_addr = extended_addr; + addr = swab64((__force u64)wpanusb->hw->phy->perm_extended_addr); + dev_info(&udev->dev, "Read permanent extended address %8phC from device\n", &addr); + } + + kfree(buffer); + return ret; +} + +/* FIXME: these need to come as capabilities from the device */ +static const s32 wpanusb_powers[] = { + 300, 280, 230, 180, 130, 70, 0, -100, -200, -300, -400, -500, -700, + -900, -1200, -1700, +}; + +static int wpanusb_get_device_capabilities(struct ieee802154_hw *hw) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + unsigned char *buffer; + int ret = 0; + + buffer = kmalloc(IEEE802154_EXTENDED_ADDR_LEN, GFP_KERNEL); + if (!buffer) + return -ENOMEM; + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), GET_EXTENDED_ADDR, buffer, + IEEE802154_EXTENDED_ADDR_LEN); + if (ret < 0) { + dev_err(&udev->dev, "failed to fetch extended address, random address set\n"); + ieee802154_random_extended_addr(&wpanusb->hw->phy->perm_extended_addr); + kfree(buffer); + return ret; + } + + /* FIXME: these need to come from device capabilities */ + hw->flags = IEEE802154_HW_TX_OMIT_CKSUM | IEEE802154_HW_AFILT | + IEEE802154_HW_PROMISCUOUS; + + /* FIXME: these need to come from device capabilities */ + hw->phy->flags = WPAN_PHY_FLAG_TXPOWER; + + /* Set default and supported channels */ + hw->phy->current_page = 0; + hw->phy->current_channel = 11; + /* FIXME: these need to come from device capabilities */ + hw->phy->supported.channels[0] = WPANUSB_VALID_CHANNELS; + + /* FIXME: these need to come from device capabilities */ + hw->phy->supported.tx_powers = wpanusb_powers; + hw->phy->supported.tx_powers_size = ARRAY_SIZE(wpanusb_powers); + hw->phy->transmit_power = hw->phy->supported.tx_powers[0]; + + kfree(buffer); + return ret; +} + +static int wpanusb_start(struct ieee802154_hw *hw) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + int ret; + + schedule_delayed_work(&wpanusb->work, 0); + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + START, NULL, 0); + if (ret < 0) { + dev_err(&udev->dev, "Failed to start ieee802154"); + usb_kill_anchored_urbs(&wpanusb->idle_urbs); + } + + return ret; +} + +static void wpanusb_stop(struct ieee802154_hw *hw) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + int ret; + + dev_dbg(&udev->dev, "stop"); + + usb_kill_anchored_urbs(&wpanusb->idle_urbs); + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + STOP, NULL, 0); + if (ret < 0) + dev_err(&udev->dev, "Failed to stop ieee802154"); +} + +static int wpanusb_set_txpower(struct ieee802154_hw *hw, s32 mbm) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + + dev_err(&udev->dev, "%s: Not handled, mbm %d", __func__, mbm); + + return -ENOTSUPP; +} + +static int wpanusb_set_cca_mode(struct ieee802154_hw *hw, + const struct wpan_phy_cca *cca) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + + dev_err(&udev->dev, "%s: Not handled, mode %u opt %u", + __func__, cca->mode, cca->opt); + + switch (cca->mode) { + case NL802154_CCA_ENERGY: + break; + case NL802154_CCA_CARRIER: + break; + case NL802154_CCA_ENERGY_CARRIER: + break; + default: + return -EINVAL; + } + + return 0; +} + +static int wpanusb_set_lbt(struct ieee802154_hw *hw, bool on) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + int ret = 0; + + if (on) + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + SET_LBT, NULL, 0); + + return ret; +} + +static int wpanusb_set_frame_retries(struct ieee802154_hw *hw, s8 retries) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + int ret; + + /* FIXME pass retries onwards to device */ + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), + SET_FRAME_RETRIES, NULL, 0); + + return ret; +} + +static int wpanusb_set_cca_ed_level(struct ieee802154_hw *hw, s32 mbm) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + + dev_err(&udev->dev, "%s: Not handled, mbm %d", __func__, mbm); + + return 0; +} + +static int wpanusb_set_csma_params(struct ieee802154_hw *hw, u8 min_be, + u8 max_be, u8 retries) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + + dev_err(&udev->dev, "%s: Not handled, min_be %u max_be %u retr %u", + __func__, min_be, max_be, retries); + + return 0; +} + +static int wpanusb_set_promiscuous_mode(struct ieee802154_hw *hw, const bool on) +{ + struct wpanusb *wpanusb = hw->priv; + struct usb_device *udev = wpanusb->udev; + + dev_err(&udev->dev, "%s: Not handled, on %d", __func__, on); + + return 0; +} + +static const struct ieee802154_ops wpanusb_ops = { + .owner = THIS_MODULE, + .xmit_async = wpanusb_xmit, + .ed = wpanusb_ed, + .set_channel = wpanusb_channel, + .start = wpanusb_start, + .stop = wpanusb_stop, + .set_hw_addr_filt = wpanusb_set_hw_addr_filt, + .set_txpower = wpanusb_set_txpower, + .set_lbt = wpanusb_set_lbt, + .set_cca_mode = wpanusb_set_cca_mode, + .set_cca_ed_level = wpanusb_set_cca_ed_level, + .set_csma_params = wpanusb_set_csma_params, + .set_frame_retries = wpanusb_set_frame_retries, + .set_promiscuous_mode = wpanusb_set_promiscuous_mode, +}; + +/* ----- Setup ------------------------------------------------------------- */ + +static int wpanusb_probe(struct usb_interface *interface, + const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(interface); + struct ieee802154_hw *hw; + struct wpanusb *wpanusb; + int ret; + + hw = ieee802154_alloc_hw(sizeof(struct wpanusb), &wpanusb_ops); + if (!hw) + return -ENOMEM; + + wpanusb = hw->priv; + wpanusb->hw = hw; + wpanusb->udev = usb_get_dev(udev); + usb_set_intfdata(interface, wpanusb); + + wpanusb->shutdown = 0; + INIT_DELAYED_WORK(&wpanusb->work, wpanusb_work_urbs); + init_usb_anchor(&wpanusb->idle_urbs); + init_usb_anchor(&wpanusb->rx_urbs); + + ret = wpanusb_alloc_urbs(wpanusb, WPANUSB_NUM_RX_URBS); + if (ret) + goto fail; + + wpanusb->tx_dr.bRequestType = VENDOR_OUT; + wpanusb->tx_dr.bRequest = TX; + wpanusb->tx_dr.wValue = cpu_to_le16(0); + + wpanusb->tx_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!wpanusb->tx_urb) + goto fail; + + hw->parent = &udev->dev; + + ret = wpanusb_control_send(wpanusb, usb_sndctrlpipe(udev, 0), RESET, + NULL, 0); + if (ret < 0) { + dev_err(&udev->dev, "Failed to RESET ieee802154"); + goto fail; + } + + ret = wpanusb_get_device_capabilities(hw); + + if (ret < 0) { + dev_err(&udev->dev, "Failed to get device capabilities"); + goto fail; + } + + ret = wpanusb_set_extended_addr(hw); + + if (ret < 0) { + dev_err(&udev->dev, "Failed to set permanent address"); + goto fail; + } + + ret = ieee802154_register_hw(hw); + if (ret) { + dev_err(&udev->dev, "Failed to register ieee802154"); + goto fail; + } + + dev_dbg(&udev->dev, "ieee802154 ready to go"); + + return 0; + +fail: + dev_err(&udev->dev, "Failed ieee802154 probe"); + wpanusb_free_urbs(wpanusb); + usb_kill_urb(wpanusb->tx_urb); + usb_free_urb(wpanusb->tx_urb); + usb_put_dev(udev); + ieee802154_free_hw(hw); + + return ret; +} + +static void wpanusb_disconnect(struct usb_interface *interface) +{ + struct wpanusb *wpanusb = usb_get_intfdata(interface); + + wpanusb->shutdown = 1; + cancel_delayed_work_sync(&wpanusb->work); + + usb_kill_anchored_urbs(&wpanusb->rx_urbs); + wpanusb_free_urbs(wpanusb); + usb_kill_urb(wpanusb->tx_urb); + usb_free_urb(wpanusb->tx_urb); + + ieee802154_unregister_hw(wpanusb->hw); + + ieee802154_free_hw(wpanusb->hw); + + usb_set_intfdata(interface, NULL); + usb_put_dev(wpanusb->udev); +} + +/* The devices we work with */ +static const struct usb_device_id wpanusb_device_table[] = { + { + USB_DEVICE_AND_INTERFACE_INFO(WPANUSB_VENDOR_ID, + WPANUSB_PRODUCT_ID, + USB_CLASS_VENDOR_SPEC, + 0, 0), + USB_DEVICE_AND_INTERFACE_INFO(BEAGLECONNECT_VENDOR_ID, + BEAGLECONNECT_PRODUCT_ID, + USB_CLASS_VENDOR_SPEC, + 0, 0) + }, + /* end with null element */ + {} +}; +MODULE_DEVICE_TABLE(usb, wpanusb_device_table); + +static struct usb_driver wpanusb_driver = { + .name = "wpanusb", + .probe = wpanusb_probe, + .disconnect = wpanusb_disconnect, + .id_table = wpanusb_device_table, +}; +module_usb_driver(wpanusb_driver); + +MODULE_AUTHOR("Andrei Emeltchenko "); +MODULE_DESCRIPTION("WPANUSB IEEE 802.15.4 over USB Driver"); +MODULE_LICENSE("GPL"); diff --git b/drivers/net/ieee802154/wpanusb.h b/drivers/net/ieee802154/wpanusb.h new file mode 100644 index 0000000..8338df3 --- /dev/null +++ b/drivers/net/ieee802154/wpanusb.h @@ -0,0 +1,53 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Definitions shared between kernel and WPANUSB firmware + * + * Copyright (C) 2018 Intel Corp. + * + * Written by Andrei Emeltchenko + */ + +#define WPANUSB_VENDOR_ID 0x2fe3 +#define WPANUSB_PRODUCT_ID 0x0101 + +#define BEAGLECONNECT_VENDOR_ID 0x2047 +#define BEAGLECONNECT_PRODUCT_ID 0x0aa5 + +enum wpanusb_requests { + RESET, + TX, + XMIT_ASYNC, + ED, + SET_CHANNEL, + START, + STOP, + SET_SHORT_ADDR, + SET_PAN_ID, + SET_IEEE_ADDR, + SET_TXPOWER, + SET_CCA_MODE, + SET_CCA_ED_LEVEL, + SET_CSMA_PARAMS, + SET_LBT, + SET_FRAME_RETRIES, + SET_PROMISCUOUS_MODE, + GET_EXTENDED_ADDR, + GET_CAPABILITIES, +}; + +struct set_channel { + __u8 page; + __u8 channel; +} __packed; + +struct set_short_addr { + __le16 short_addr; +} __packed; + +struct set_pan_id { + __le16 pan_id; +} __packed; + +struct set_ieee_addr { + __le64 ieee_addr; +} __packed; diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c index a9a6b63..053cecf 100644 --- a/drivers/net/wireless/ti/wl12xx/main.c +++ b/drivers/net/wireless/ti/wl12xx/main.c @@ -635,7 +635,6 @@ static int wl12xx_identify_chip(struct wl1271 *wl) wl->quirks |= WLCORE_QUIRK_LEGACY_NVS | WLCORE_QUIRK_DUAL_PROBE_TMPL | WLCORE_QUIRK_TKIP_HEADER_SPACE | - WLCORE_QUIRK_START_STA_FAILS | WLCORE_QUIRK_AP_ZERO_SESSION_ID; wl->sr_fw_name = WL127X_FW_NAME_SINGLE; wl->mr_fw_name = WL127X_FW_NAME_MULTI; @@ -659,7 +658,6 @@ static int wl12xx_identify_chip(struct wl1271 *wl) wl->quirks |= WLCORE_QUIRK_LEGACY_NVS | WLCORE_QUIRK_DUAL_PROBE_TMPL | WLCORE_QUIRK_TKIP_HEADER_SPACE | - WLCORE_QUIRK_START_STA_FAILS | WLCORE_QUIRK_AP_ZERO_SESSION_ID; wl->plt_fw_name = WL127X_PLT_FW_NAME; wl->sr_fw_name = WL127X_FW_NAME_SINGLE; @@ -688,7 +686,6 @@ static int wl12xx_identify_chip(struct wl1271 *wl) wl->quirks |= WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN | WLCORE_QUIRK_DUAL_PROBE_TMPL | WLCORE_QUIRK_TKIP_HEADER_SPACE | - WLCORE_QUIRK_START_STA_FAILS | WLCORE_QUIRK_AP_ZERO_SESSION_ID; wlcore_set_min_fw_ver(wl, WL128X_CHIP_VER, diff --git a/drivers/net/wireless/ti/wlcore/main.c b/drivers/net/wireless/ti/wlcore/main.c index a635887..386e9c6 100644 --- a/drivers/net/wireless/ti/wlcore/main.c +++ b/drivers/net/wireless/ti/wlcore/main.c @@ -2872,21 +2872,8 @@ static int wlcore_join(struct wl1271 *wl, struct wl12xx_vif *wlvif) if (is_ibss) ret = wl12xx_cmd_role_start_ibss(wl, wlvif); - else { - if (wl->quirks & WLCORE_QUIRK_START_STA_FAILS) { - /* - * TODO: this is an ugly workaround for wl12xx fw - * bug - we are not able to tx/rx after the first - * start_sta, so make dummy start+stop calls, - * and then call start_sta again. - * this should be fixed in the fw. - */ - wl12xx_cmd_role_start_sta(wl, wlvif); - wl12xx_cmd_role_stop_sta(wl, wlvif); - } - + else ret = wl12xx_cmd_role_start_sta(wl, wlvif); - } return ret; } @@ -5394,7 +5381,7 @@ static int wl1271_op_ampdu_action(struct ieee80211_hw *hw, if (wl->ba_rx_session_count >= wl->ba_rx_session_count_max) { ret = -EBUSY; - wl1271_error("exceeded max RX BA sessions"); + wl1271_debug(DEBUG_RX, "exceeded max RX BA sessions"); break; } diff --git a/drivers/net/wireless/ti/wlcore/wlcore.h b/drivers/net/wireless/ti/wlcore/wlcore.h index b782131..81c94d3 100644 --- a/drivers/net/wireless/ti/wlcore/wlcore.h +++ b/drivers/net/wireless/ti/wlcore/wlcore.h @@ -547,9 +547,6 @@ wlcore_set_min_fw_ver(struct wl1271 *wl, unsigned int chip, /* Each RX/TX transaction requires an end-of-transaction transfer */ #define WLCORE_QUIRK_END_OF_TRANSACTION BIT(0) -/* the first start_role(sta) sometimes doesn't work on wl12xx */ -#define WLCORE_QUIRK_START_STA_FAILS BIT(1) - /* wl127x and SPI don't support SDIO block size alignment */ #define WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN BIT(2) diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 696bf77..05cdb76 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0-only source "drivers/power/reset/Kconfig" source "drivers/power/supply/Kconfig" +source "drivers/power/pwrseq/Kconfig" diff --git a/drivers/power/Makefile b/drivers/power/Makefile index effbf03..081844e 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0-only obj-$(CONFIG_POWER_RESET) += reset/ obj-$(CONFIG_POWER_SUPPLY) += supply/ +obj-$(CONFIG_POWER_SEQUENCE) += pwrseq/ diff --git b/drivers/power/pwrseq/Kconfig b/drivers/power/pwrseq/Kconfig new file mode 100644 index 0000000..c6b3569 --- /dev/null +++ b/drivers/power/pwrseq/Kconfig @@ -0,0 +1,20 @@ +# +# Power Sequence library +# + +menuconfig POWER_SEQUENCE + bool "Power sequence control" + help + It is used for drivers which needs to do power sequence + (eg, turn on clock, toggle reset gpio) before the related + devices can be found by hardware, eg, USB bus. + +if POWER_SEQUENCE + +config PWRSEQ_GENERIC + bool "Generic power sequence control" + depends on OF + help + This is the generic power sequence control library, and is + supposed to support common power sequence usage. +endif diff --git b/drivers/power/pwrseq/Makefile b/drivers/power/pwrseq/Makefile new file mode 100644 index 0000000..ad82389 --- /dev/null +++ b/drivers/power/pwrseq/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_POWER_SEQUENCE) += core.o +obj-$(CONFIG_PWRSEQ_GENERIC) += pwrseq_generic.o diff --git b/drivers/power/pwrseq/core.c b/drivers/power/pwrseq/core.c new file mode 100644 index 0000000..3d19e62 --- /dev/null +++ b/drivers/power/pwrseq/core.c @@ -0,0 +1,335 @@ +/* + * core.c power sequence core file + * + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Author: Peter Chen + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 of + * the License as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. + */ + +#include +#include +#include +#include +#include + +static DEFINE_MUTEX(pwrseq_list_mutex); +static LIST_HEAD(pwrseq_list); + +static int pwrseq_get(struct device_node *np, struct pwrseq *p) +{ + if (p && p->get) + return p->get(np, p); + + return -ENOTSUPP; +} + +static int pwrseq_on(struct pwrseq *p) +{ + if (p && p->on) + return p->on(p); + + return -ENOTSUPP; +} + +static void pwrseq_off(struct pwrseq *p) +{ + if (p && p->off) + p->off(p); +} + +static void pwrseq_put(struct pwrseq *p) +{ + if (p && p->put) + p->put(p); +} + +/** + * pwrseq_register - Add pwrseq instance to global pwrseq list + * + * @pwrseq: the pwrseq instance + */ +void pwrseq_register(struct pwrseq *pwrseq) +{ + mutex_lock(&pwrseq_list_mutex); + list_add(&pwrseq->node, &pwrseq_list); + mutex_unlock(&pwrseq_list_mutex); +} +EXPORT_SYMBOL_GPL(pwrseq_register); + +/** + * pwrseq_unregister - Remove pwrseq instance from global pwrseq list + * + * @pwrseq: the pwrseq instance + */ +void pwrseq_unregister(struct pwrseq *pwrseq) +{ + mutex_lock(&pwrseq_list_mutex); + list_del(&pwrseq->node); + mutex_unlock(&pwrseq_list_mutex); +} +EXPORT_SYMBOL_GPL(pwrseq_unregister); + +static struct pwrseq *pwrseq_find_available_instance(struct device_node *np) +{ + struct pwrseq *pwrseq; + + mutex_lock(&pwrseq_list_mutex); + list_for_each_entry(pwrseq, &pwrseq_list, node) { + if (pwrseq->used) + continue; + + /* compare compatible string for pwrseq node */ + if (of_match_node(pwrseq->pwrseq_of_match_table, np)) { + pwrseq->used = true; + mutex_unlock(&pwrseq_list_mutex); + return pwrseq; + } + + /* return generic pwrseq instance */ + if (!strcmp(pwrseq->pwrseq_of_match_table->compatible, + "generic")) { + pr_debug("using generic pwrseq instance for %s\n", + np->full_name); + pwrseq->used = true; + mutex_unlock(&pwrseq_list_mutex); + return pwrseq; + } + } + mutex_unlock(&pwrseq_list_mutex); + pr_debug("Can't find any pwrseq instances for %s\n", np->full_name); + + return NULL; +} + +/** + * of_pwrseq_on - Carry out power sequence on for device node + * + * @np: the device node would like to power on + * + * Carry out a single device power on. If multiple devices + * need to be handled, use of_pwrseq_on_list() instead. + * + * Return a pointer to the power sequence instance on success, + * or an error code otherwise. + */ +struct pwrseq *of_pwrseq_on(struct device_node *np) +{ + struct pwrseq *pwrseq; + int ret; + + pwrseq = pwrseq_find_available_instance(np); + if (!pwrseq) + return ERR_PTR(-ENOENT); + + ret = pwrseq_get(np, pwrseq); + if (ret) { + /* Mark current pwrseq as unused */ + pwrseq->used = false; + return ERR_PTR(ret); + } + + ret = pwrseq_on(pwrseq); + if (ret) + goto pwr_put; + + return pwrseq; + +pwr_put: + pwrseq_put(pwrseq); + return ERR_PTR(ret); +} +EXPORT_SYMBOL_GPL(of_pwrseq_on); + +/** + * of_pwrseq_off - Carry out power sequence off for this pwrseq instance + * + * @pwrseq: the pwrseq instance which related device would like to be off + * + * This API is used to power off single device, it is the opposite + * operation for of_pwrseq_on. + */ +void of_pwrseq_off(struct pwrseq *pwrseq) +{ + pwrseq_off(pwrseq); + pwrseq_put(pwrseq); +} +EXPORT_SYMBOL_GPL(of_pwrseq_off); + +/** + * of_pwrseq_on_list - Carry out power sequence on for list + * + * @np: the device node would like to power on + * @head: the list head for pwrseq list on this bus + * + * This API is used to power on multiple devices at single bus. + * If there are several devices on bus (eg, USB bus), uses this + * this API. Otherwise, use of_pwrseq_on instead. After the device + * is powered on successfully, it will be added to pwrseq list for + * this bus. The caller needs to use mutex_lock for concurrent. + * + * Return 0 on success, or an error value otherwise. + */ +int of_pwrseq_on_list(struct device_node *np, struct list_head *head) +{ + struct pwrseq *pwrseq; + struct pwrseq_list_per_dev *pwrseq_list_node; + + pwrseq_list_node = kzalloc(sizeof(*pwrseq_list_node), GFP_KERNEL); + if (!pwrseq_list_node) + return -ENOMEM; + + pwrseq = of_pwrseq_on(np); + if (IS_ERR(pwrseq)) { + kfree(pwrseq_list_node); + return PTR_ERR(pwrseq); + } + + pwrseq_list_node->pwrseq = pwrseq; + list_add(&pwrseq_list_node->list, head); + + return 0; +} +EXPORT_SYMBOL_GPL(of_pwrseq_on_list); + +/** + * of_pwrseq_off_list - Carry out power sequence off for the list + * + * @head: the list head for pwrseq instance list on this bus + * + * This API is used to power off all devices on this bus, it is + * the opposite operation for of_pwrseq_on_list. + * The caller needs to use mutex_lock for concurrent. + */ +void of_pwrseq_off_list(struct list_head *head) +{ + struct pwrseq *pwrseq; + struct pwrseq_list_per_dev *pwrseq_list_node, *tmp_node; + + list_for_each_entry_safe(pwrseq_list_node, tmp_node, head, list) { + pwrseq = pwrseq_list_node->pwrseq; + of_pwrseq_off(pwrseq); + list_del(&pwrseq_list_node->list); + kfree(pwrseq_list_node); + } +} +EXPORT_SYMBOL_GPL(of_pwrseq_off_list); + +/** + * pwrseq_suspend - Carry out power sequence suspend for this pwrseq instance + * + * @pwrseq: the pwrseq instance + * + * This API is used to do suspend operation on pwrseq instance. + * + * Return 0 on success, or an error value otherwise. + */ +int pwrseq_suspend(struct pwrseq *p) +{ + int ret = 0; + + if (p && p->suspend) + ret = p->suspend(p); + else + return ret; + + if (!ret) + p->suspended = true; + else + pr_err("%s failed\n", __func__); + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_suspend); + +/** + * pwrseq_resume - Carry out power sequence resume for this pwrseq instance + * + * @pwrseq: the pwrseq instance + * + * This API is used to do resume operation on pwrseq instance. + * + * Return 0 on success, or an error value otherwise. + */ +int pwrseq_resume(struct pwrseq *p) +{ + int ret = 0; + + if (p && p->resume) + ret = p->resume(p); + else + return ret; + + if (!ret) + p->suspended = false; + else + pr_err("%s failed\n", __func__); + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_resume); + +/** + * pwrseq_suspend_list - Carry out power sequence suspend for list + * + * @head: the list head for pwrseq instance list on this bus + * + * This API is used to do suspend on all power sequence instances on this bus. + * The caller needs to use mutex_lock for concurrent. + */ +int pwrseq_suspend_list(struct list_head *head) +{ + struct pwrseq *pwrseq; + struct pwrseq_list_per_dev *pwrseq_list_node; + int ret = 0; + + list_for_each_entry(pwrseq_list_node, head, list) { + ret = pwrseq_suspend(pwrseq_list_node->pwrseq); + if (ret) + break; + } + + if (ret) { + list_for_each_entry(pwrseq_list_node, head, list) { + pwrseq = pwrseq_list_node->pwrseq; + if (pwrseq->suspended) + pwrseq_resume(pwrseq); + } + } + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_suspend_list); + +/** + * pwrseq_resume_list - Carry out power sequence resume for the list + * + * @head: the list head for pwrseq instance list on this bus + * + * This API is used to do resume on all power sequence instances on this bus. + * The caller needs to use mutex_lock for concurrent. + */ +int pwrseq_resume_list(struct list_head *head) +{ + struct pwrseq_list_per_dev *pwrseq_list_node; + int ret = 0; + + list_for_each_entry(pwrseq_list_node, head, list) { + ret = pwrseq_resume(pwrseq_list_node->pwrseq); + if (ret) + break; + } + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_resume_list); diff --git b/drivers/power/pwrseq/pwrseq_generic.c b/drivers/power/pwrseq/pwrseq_generic.c new file mode 100644 index 0000000..4e7c090 --- /dev/null +++ b/drivers/power/pwrseq/pwrseq_generic.c @@ -0,0 +1,234 @@ +/* + * pwrseq_generic.c Generic power sequence handling + * + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Author: Peter Chen + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 of + * the License as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include + +struct pwrseq_generic { + struct pwrseq pwrseq; + struct gpio_desc *gpiod_reset; + struct clk *clks[PWRSEQ_MAX_CLKS]; + u32 duration_us; + bool suspended; +}; + +#define to_generic_pwrseq(p) container_of(p, struct pwrseq_generic, pwrseq) + +static int pwrseq_generic_alloc_instance(void); +static const struct of_device_id generic_id_table[] = { + { .compatible = "generic",}, + { /* sentinel */ } +}; + +static int pwrseq_generic_suspend(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk; + + for (clk = PWRSEQ_MAX_CLKS - 1; clk >= 0; clk--) + clk_disable_unprepare(pwrseq_gen->clks[clk]); + + pwrseq_gen->suspended = true; + return 0; +} + +static int pwrseq_generic_resume(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk, ret = 0; + + for (clk = 0; clk < PWRSEQ_MAX_CLKS && pwrseq_gen->clks[clk]; clk++) { + ret = clk_prepare_enable(pwrseq_gen->clks[clk]); + if (ret) { + pr_err("Can't enable clock, ret=%d\n", ret); + goto err_disable_clks; + } + } + + pwrseq_gen->suspended = false; + return ret; + +err_disable_clks: + while (--clk >= 0) + clk_disable_unprepare(pwrseq_gen->clks[clk]); + + return ret; +} + +static void pwrseq_generic_put(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk; + + if (pwrseq_gen->gpiod_reset) + gpiod_put(pwrseq_gen->gpiod_reset); + + for (clk = 0; clk < PWRSEQ_MAX_CLKS; clk++) + clk_put(pwrseq_gen->clks[clk]); + + pwrseq_unregister(&pwrseq_gen->pwrseq); + kfree(pwrseq_gen); +} + +static void pwrseq_generic_off(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk; + + if (pwrseq_gen->suspended) + return; + + for (clk = PWRSEQ_MAX_CLKS - 1; clk >= 0; clk--) + clk_disable_unprepare(pwrseq_gen->clks[clk]); +} + +static int pwrseq_generic_on(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk, ret = 0; + struct gpio_desc *gpiod_reset = pwrseq_gen->gpiod_reset; + + for (clk = 0; clk < PWRSEQ_MAX_CLKS && pwrseq_gen->clks[clk]; clk++) { + ret = clk_prepare_enable(pwrseq_gen->clks[clk]); + if (ret) { + pr_err("Can't enable clock, ret=%d\n", ret); + goto err_disable_clks; + } + } + + if (gpiod_reset) { + u32 duration_us = pwrseq_gen->duration_us; + + if (duration_us <= 10) + udelay(10); + else + usleep_range(duration_us, duration_us + 100); + gpiod_set_value(gpiod_reset, 0); + } + + return ret; + +err_disable_clks: + while (--clk >= 0) + clk_disable_unprepare(pwrseq_gen->clks[clk]); + + return ret; +} + +static int pwrseq_generic_get(struct device_node *np, struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + enum of_gpio_flags flags; + int reset_gpio, clk, ret = 0; + + for (clk = 0; clk < PWRSEQ_MAX_CLKS; clk++) { + pwrseq_gen->clks[clk] = of_clk_get(np, clk); + if (IS_ERR(pwrseq_gen->clks[clk])) { + ret = PTR_ERR(pwrseq_gen->clks[clk]); + if (ret != -ENOENT) + goto err_put_clks; + pwrseq_gen->clks[clk] = NULL; + break; + } + } + + reset_gpio = of_get_named_gpio_flags(np, "reset-gpios", 0, &flags); + if (gpio_is_valid(reset_gpio)) { + unsigned long gpio_flags; + + if (flags & OF_GPIO_ACTIVE_LOW) + gpio_flags = GPIOF_ACTIVE_LOW | GPIOF_OUT_INIT_LOW; + else + gpio_flags = GPIOF_OUT_INIT_HIGH; + + ret = gpio_request_one(reset_gpio, gpio_flags, + "pwrseq-reset-gpios"); + if (ret) + goto err_put_clks; + + pwrseq_gen->gpiod_reset = gpio_to_desc(reset_gpio); + of_property_read_u32(np, "reset-duration-us", + &pwrseq_gen->duration_us); + } else if (reset_gpio == -ENOENT) { + ; /* no such gpio */ + } else { + ret = reset_gpio; + pr_err("Failed to get reset gpio on %s, err = %d\n", + np->full_name, reset_gpio); + goto err_put_clks; + } + + /* allocate new one for later pwrseq instance request */ + ret = pwrseq_generic_alloc_instance(); + if (ret) + goto err_put_gpio; + + return 0; + +err_put_gpio: + if (pwrseq_gen->gpiod_reset) + gpiod_put(pwrseq_gen->gpiod_reset); +err_put_clks: + while (--clk >= 0) + clk_put(pwrseq_gen->clks[clk]); + return ret; +} + +/** + * pwrseq_generic_alloc_instance - power sequence instance allocation + * + * This function is used to allocate one generic power sequence instance, + * it is called when the system boots up and after one power sequence + * instance is got successfully. + * + * Return zero on success or an error code otherwise. + */ +static int pwrseq_generic_alloc_instance(void) +{ + struct pwrseq_generic *pwrseq_gen; + + pwrseq_gen = kzalloc(sizeof(*pwrseq_gen), GFP_KERNEL); + if (!pwrseq_gen) + return -ENOMEM; + + pwrseq_gen->pwrseq.pwrseq_of_match_table = generic_id_table; + pwrseq_gen->pwrseq.get = pwrseq_generic_get; + pwrseq_gen->pwrseq.on = pwrseq_generic_on; + pwrseq_gen->pwrseq.off = pwrseq_generic_off; + pwrseq_gen->pwrseq.put = pwrseq_generic_put; + pwrseq_gen->pwrseq.suspend = pwrseq_generic_suspend; + pwrseq_gen->pwrseq.resume = pwrseq_generic_resume; + + pwrseq_register(&pwrseq_gen->pwrseq); + return 0; +} + +/* Allocate one pwrseq instance during boots up */ +static int __init pwrseq_generic_register(void) +{ + return pwrseq_generic_alloc_instance(); +} +postcore_initcall(pwrseq_generic_register) diff --git a/drivers/regulator/twl6030-regulator.c b/drivers/regulator/twl6030-regulator.c index 430265c..99f7eb8 100644 --- a/drivers/regulator/twl6030-regulator.c +++ b/drivers/regulator/twl6030-regulator.c @@ -299,6 +299,13 @@ static const struct regulator_ops twl6030fixed_ops = { .get_status = twl6030reg_get_status, }; +static struct regulator_ops twl6030_fixed_resource = { + .enable = twl6030reg_enable, + .disable = twl6030reg_disable, + .is_enabled = twl6030reg_is_enabled, + .get_status = twl6030reg_get_status, +}; + /* * SMPS status and control */ @@ -572,6 +579,19 @@ static const struct twlreg_info TWLSMPS_INFO_##label = { \ }, \ } +#define TWL6030_FIXED_RESOURCE(label, offset, turnon_delay) \ +static struct twlreg_info TWLRES_INFO_##label = { \ + .base = offset, \ + .desc = { \ + .name = #label, \ + .id = TWL6030_REG_##label, \ + .ops = &twl6030_fixed_resource, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .enable_time = turnon_delay, \ + }, \ + } + /* VUSBCP is managed *only* by the USB subchip */ /* 6030 REG with base as PMC Slave Misc : 0x0030 */ /* Turnon-delay and remap configuration values for 6030 are not @@ -601,6 +621,7 @@ TWL6030_FIXED_LDO(VDAC, 0x64, 1800, 0); TWL6030_FIXED_LDO(VUSB, 0x70, 3300, 0); TWL6030_FIXED_LDO(V1V8, 0x16, 1800, 0); TWL6030_FIXED_LDO(V2V1, 0x1c, 2100, 0); +TWL6030_FIXED_RESOURCE(CLK32KG, 0x8C, 0); TWL6032_ADJUSTABLE_SMPS(SMPS3, 0x34); TWL6032_ADJUSTABLE_SMPS(SMPS4, 0x10); TWL6032_ADJUSTABLE_SMPS(VIO, 0x16); @@ -632,6 +653,7 @@ static u8 twl_get_smps_mult(void) #define TWL6030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6030, label) #define TWL6032_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6032, label) #define TWLFIXED_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLFIXED, label) +#define TWLRES_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLRES, label) #define TWLSMPS_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLSMPS, label) static const struct of_device_id twl_of_match[] = { @@ -659,6 +681,7 @@ static const struct of_device_id twl_of_match[] = { TWLFIXED_OF_MATCH("ti,twl6030-vusb", VUSB), TWLFIXED_OF_MATCH("ti,twl6030-v1v8", V1V8), TWLFIXED_OF_MATCH("ti,twl6030-v2v1", V2V1), + TWLRES_OF_MATCH("ti,twl6030-clk32kg", CLK32KG), TWLSMPS_OF_MATCH("ti,twl6032-smps3", SMPS3), TWLSMPS_OF_MATCH("ti,twl6032-smps4", SMPS4), TWLSMPS_OF_MATCH("ti,twl6032-vio", VIO), diff --git a/drivers/spi/spidev.c b/drivers/spi/spidev.c index 8cb4d92..871c188 100644 --- a/drivers/spi/spidev.c +++ b/drivers/spi/spidev.c @@ -738,9 +738,9 @@ static int spidev_probe(struct spi_device *spi) * compatible string, it is a Linux implementation thing * rather than a description of the hardware. */ - WARN(spi->dev.of_node && - of_device_is_compatible(spi->dev.of_node, "spidev"), - "%pOF: buggy DT: spidev listed directly in DT\n", spi->dev.of_node); +// WARN(spi->dev.of_node && +// of_device_is_compatible(spi->dev.of_node, "spidev"), +// "%pOF: buggy DT: spidev listed directly in DT\n", spi->dev.of_node); spidev_probe_acpi(spi); diff --git a/drivers/staging/fbtft/fb_ssd1306.c b/drivers/staging/fbtft/fb_ssd1306.c index 6cf9df5..4cd6161 100644 --- a/drivers/staging/fbtft/fb_ssd1306.c +++ b/drivers/staging/fbtft/fb_ssd1306.c @@ -55,6 +55,9 @@ static int init_display(struct fbtft_par *par) write_reg(par, 0x3F); else if (par->info->var.yres == 48) write_reg(par, 0x2F); + else if (par->info->var.yres == 39) + /* https://libstock.mikroe.com/projects/download/1111/2577/1411057038_oled_b_click___e_mikroc_arm.zip */ + write_reg(par, 0x27); else write_reg(par, 0x1F); @@ -76,19 +79,27 @@ static int init_display(struct fbtft_par *par) write_reg(par, 0x01); /* Set Segment Re-map */ - /* column address 127 is mapped to SEG0 */ - write_reg(par, 0xA0 | 0x1); + if (par->info->var.yres == 39) + /* no segment re-map */ + write_reg(par, 0xA0 | 0x0); + else + /* column address 127 is mapped to SEG0 */ + write_reg(par, 0xA0 | 0x1); /* Set COM Output Scan Direction */ - /* remapped mode. Scan from COM[N-1] to COM0 */ - write_reg(par, 0xC8); + if (par->info->var.yres == 39) + /* no columnt re-map mode. Scan from COM0 to COM[N-1] */ + write_reg(par, 0xC0); + else + /* remapped mode. Scan from COM[N-1] to COM0 */ + write_reg(par, 0xC8); /* Set COM Pins Hardware Configuration */ write_reg(par, 0xDA); if (par->info->var.yres == 64) /* A[4]=1b, Alternative COM pin configuration */ write_reg(par, 0x12); - else if (par->info->var.yres == 48) + else if (par->info->var.yres == 48 || par->info->var.yres == 39) /* A[4]=1b, Alternative COM pin configuration */ write_reg(par, 0x12); else @@ -97,12 +108,18 @@ static int init_display(struct fbtft_par *par) /* Set Pre-charge Period */ write_reg(par, 0xD9); - write_reg(par, 0xF1); + if (par->info->var.yres == 39) + write_reg(par, 0x25); + else + write_reg(par, 0xF1); /* Set VCOMH Deselect Level */ write_reg(par, 0xDB); - /* according to the datasheet, this value is out of bounds */ - write_reg(par, 0x40); + if (par->info->var.yres == 39) + write_reg(par, 0x20); + else + /* according to the datasheet, this value is out of bounds */ + write_reg(par, 0x40); /* Entire Display ON */ /* Resume to RAM content display. Output follows RAM content */ @@ -133,6 +150,20 @@ static void set_addr_win_64x48(struct fbtft_par *par) write_reg(par, 0x5); } +static void set_addr_win_96x39(struct fbtft_par *par) +{ + /* Set Page Address */ + write_reg(par, 0xB0); + /* Set Column Address */ + write_reg(par, 0x21); + write_reg(par, 0x00); + write_reg(par, 0x5F); + /* Set Page Address Range */ + write_reg(par, 0x22); + write_reg(par, 0x0); + write_reg(par, 0x4); +} + static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye) { /* Set Lower Column Start Address for Page Addressing Mode */ @@ -144,6 +175,8 @@ static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye) if (par->info->var.xres == 64 && par->info->var.yres == 48) set_addr_win_64x48(par); + else if (par->info->var.xres == 96 && par->info->var.yres == 39) + set_addr_win_96x39(par); } static int blank(struct fbtft_par *par, bool on) @@ -188,11 +221,19 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len) *buf |= BIT(i); buf++; } + if (yres % 8) { + *buf = 0x00; + for (i = 0; i < (yres - (y * 8)); i++) + if (vmem16[(y * 8 + i) * xres + x]) + *buf |= BIT(i); + buf++; + y++; + } } /* Write data */ gpiod_set_value(par->gpio.dc, 1); - ret = par->fbtftops.write(par, par->txbuf.buf, xres * yres / 8); + ret = par->fbtftops.write(par, par->txbuf.buf, xres * (yres / 8 + (yres % 8 != 0))); if (ret < 0) dev_err(par->info->device, "write failed and returned: %d\n", ret); diff --git a/drivers/tty/serdev/core.c b/drivers/tty/serdev/core.c index aead0c0..685d44a 100644 --- a/drivers/tty/serdev/core.c +++ b/drivers/tty/serdev/core.c @@ -27,12 +27,17 @@ static ssize_t modalias_show(struct device *dev, struct device_attribute *attr, char *buf) { int len; + struct serdev_device *serdev = to_serdev_device(dev); len = acpi_device_modalias(dev, buf, PAGE_SIZE - 1); if (len != -ENODEV) return len; - return of_device_modalias(dev, buf, PAGE_SIZE); + len = of_device_modalias(dev, buf, PAGE_SIZE); + if (len != -ENODEV) + return len; + + return sprintf(buf, "%s%s\n", SERDEV_MODULE_PREFIX, serdev->modalias); } static DEVICE_ATTR_RO(modalias); @@ -45,14 +50,18 @@ ATTRIBUTE_GROUPS(serdev_device); static int serdev_device_uevent(struct device *dev, struct kobj_uevent_env *env) { int rc; - - /* TODO: platform modalias */ + struct serdev_device *serdev = to_serdev_device(dev); rc = acpi_device_uevent_modalias(dev, env); if (rc != -ENODEV) return rc; - return of_device_uevent_modalias(dev, env); + rc = of_device_uevent_modalias(dev, env); + if (rc != -ENODEV) + return rc; + + return add_uevent_var(env, "MODALIAS=%s%s", SERDEV_MODULE_PREFIX, + serdev->modalias); } static void serdev_device_release(struct device *dev) @@ -83,16 +92,36 @@ static const struct device_type serdev_ctrl_type = { .release = serdev_ctrl_release, }; +static int serdev_match_id(const struct serdev_device_id *id, + const struct serdev_device *sdev) +{ + while (id->name[0]) { + if (!strcmp(sdev->modalias, id->name)) + return 1; + id++; + } + + return 0; +} + static int serdev_device_match(struct device *dev, struct device_driver *drv) { + const struct serdev_device *sdev = to_serdev_device(dev); + const struct serdev_device_driver *sdrv = to_serdev_device_driver(drv); + if (!is_serdev_device(dev)) return 0; - /* TODO: platform matching */ if (acpi_driver_match_device(dev, drv)) return 1; - return of_driver_match_device(dev, drv); + if (of_driver_match_device(dev, drv)) + return 1; + + if (sdrv->id_table) + return serdev_match_id(sdrv->id_table, sdev); + + return strcmp(sdev->modalias, drv->name) == 0; } /** @@ -553,6 +582,17 @@ static int of_serdev_register_devices(struct serdev_controller *ctrl) return 0; } +struct serdev_controller *of_find_serdev_controller_by_node(struct device_node *node) +{ + struct device *dev = bus_find_device_by_of_node(&serdev_bus_type, node); + + if (!dev) + return NULL; + + return (dev->type == &serdev_ctrl_type) ? to_serdev_controller(dev) : NULL; +} +EXPORT_SYMBOL_GPL(of_find_serdev_controller_by_node); + #ifdef CONFIG_ACPI #define SERDEV_ACPI_MAX_SCAN_DEPTH 32 @@ -750,6 +790,12 @@ int serdev_controller_add(struct serdev_controller *ctrl) pm_runtime_enable(&ctrl->dev); + /* provide option to not delete a serdev controller without devices + * if property is present + */ + if (device_property_present(&ctrl->dev, "force-empty-serdev-controller")) + return 0; + ret_of = of_serdev_register_devices(ctrl); ret_acpi = acpi_serdev_register_devices(ctrl); if (ret_of && ret_acpi) { diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index 23e0dec..4d1a93f 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -1645,10 +1645,10 @@ static int __init omap8250_console_fixup(void) } add_preferred_console("ttyS", idx, options); - pr_err("WARNING: Your 'console=ttyO%d' has been replaced by 'ttyS%d'\n", + pr_info("WARNING: Your 'console=ttyO%d' has been replaced by 'ttyS%d'\n", idx, idx); - pr_err("This ensures that you still see kernel messages. Please\n"); - pr_err("update your kernel commandline.\n"); + pr_info("This ensures that you still see kernel messages. Please\n"); + pr_info("update your kernel commandline.\n"); return 0; } console_initcall(omap8250_console_fixup); diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index 26475b4..994037e 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -46,6 +46,7 @@ config USB depends on USB_ARCH_HAS_HCD select GENERIC_ALLOCATOR select USB_COMMON + select POWER_SEQUENCE select NLS # for UTF-8 strings help Universal Serial Bus (USB) is a specification for a serial bus diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 7f71218..73a0e56 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -30,6 +30,7 @@ #include #include #include +#include #include #include @@ -1714,6 +1715,7 @@ static void hub_disconnect(struct usb_interface *intf) hub->error = 0; hub_quiesce(hub, HUB_DISCONNECT); + of_pwrseq_off_list(&hub->pwrseq_on_list); mutex_lock(&usb_port_peer_mutex); /* Avoid races with recursively_mark_NOTATTACHED() */ @@ -1764,11 +1766,41 @@ static bool hub_descriptor_is_sane(struct usb_host_interface *desc) return true; } +#ifdef CONFIG_OF +static int hub_of_pwrseq_on(struct usb_hub *hub) +{ + struct device *parent; + struct usb_device *hdev = hub->hdev; + struct device_node *np; + int ret; + + if (hdev->parent) + parent = &hdev->dev; + else + parent = bus_to_hcd(hdev->bus)->self.sysdev; + + for_each_child_of_node(parent->of_node, np) { + ret = of_pwrseq_on_list(np, &hub->pwrseq_on_list); + /* Maybe no power sequence library is chosen */ + if (ret && ret != -ENOENT) + return ret; + } + + return 0; +} +#else +static int hub_of_pwrseq_on(struct usb_hub *hub) +{ + return 0; +} +#endif + static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) { struct usb_host_interface *desc; struct usb_device *hdev; struct usb_hub *hub; + int ret = -ENODEV; desc = intf->cur_altsetting; hdev = interface_to_usbdev(intf); @@ -1859,6 +1891,7 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) INIT_DELAYED_WORK(&hub->leds, led_work); INIT_DELAYED_WORK(&hub->init_work, NULL); INIT_WORK(&hub->events, hub_event); + INIT_LIST_HEAD(&hub->pwrseq_on_list); spin_lock_init(&hub->irq_urb_lock); timer_setup(&hub->irq_urb_retry, hub_retry_irq_urb, 0); usb_get_intf(intf); @@ -1879,11 +1912,14 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) usb_autopm_get_interface_no_resume(intf); } - if (hub_configure(hub, &desc->endpoint[0].desc) >= 0) - return 0; + if (hub_configure(hub, &desc->endpoint[0].desc) >= 0) { + ret = hub_of_pwrseq_on(hub); + if (!ret) + return 0; + } hub_disconnect(intf); - return -ENODEV; + return ret; } static int @@ -3763,7 +3799,7 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg) /* stop hub_wq and related activity */ hub_quiesce(hub, HUB_SUSPEND); - return 0; + return pwrseq_suspend_list(&hub->pwrseq_on_list); } /* Report wakeup requests from the ports of a resuming root hub */ @@ -3803,8 +3839,13 @@ static void report_wakeup_requests(struct usb_hub *hub) static int hub_resume(struct usb_interface *intf) { struct usb_hub *hub = usb_get_intfdata(intf); + int ret; dev_dbg(&intf->dev, "%s\n", __func__); + ret = pwrseq_resume_list(&hub->pwrseq_on_list); + if (ret) + return ret; + hub_activate(hub, HUB_RESUME); /* diff --git a/drivers/usb/core/hub.h b/drivers/usb/core/hub.h index 73f4482..dc4fd59 100644 --- a/drivers/usb/core/hub.h +++ b/drivers/usb/core/hub.h @@ -73,6 +73,7 @@ struct usb_hub { spinlock_t irq_urb_lock; struct timer_list irq_urb_retry; struct usb_port **ports; + struct list_head pwrseq_on_list; /* powered pwrseq node list */ }; /** diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h index c425290..e9477fb 100644 --- a/include/linux/mod_devicetable.h +++ b/include/linux/mod_devicetable.h @@ -486,6 +486,16 @@ struct i3c_device_id { const void *data; }; +/* serdev */ + +#define SERDEV_NAME_SIZE 32 +#define SERDEV_MODULE_PREFIX "serdev:" + +struct serdev_device_id { + char name[SERDEV_NAME_SIZE]; + kernel_ulong_t driver_data; +}; + /* spi */ #define SPI_NAME_SIZE 32 diff --git b/include/linux/power/pwrseq.h b/include/linux/power/pwrseq.h new file mode 100644 index 0000000..cbc344c --- /dev/null +++ b/include/linux/power/pwrseq.h @@ -0,0 +1,81 @@ +#ifndef __LINUX_PWRSEQ_H +#define __LINUX_PWRSEQ_H + +#include + +#define PWRSEQ_MAX_CLKS 3 + +/** + * struct pwrseq - the power sequence structure + * @pwrseq_of_match_table: the OF device id table this pwrseq library supports + * @node: the list pointer to be added to pwrseq list + * @get: the API is used to get pwrseq instance from the device node + * @on: do power on for this pwrseq instance + * @off: do power off for this pwrseq instance + * @put: release the resources on this pwrseq instance + * @suspend: do suspend operation on this pwrseq instance + * @resume: do resume operation on this pwrseq instance + * @used: this pwrseq instance is used by device + */ +struct pwrseq { + const struct of_device_id *pwrseq_of_match_table; + struct list_head node; + int (*get)(struct device_node *np, struct pwrseq *p); + int (*on)(struct pwrseq *p); + void (*off)(struct pwrseq *p); + void (*put)(struct pwrseq *p); + int (*suspend)(struct pwrseq *p); + int (*resume)(struct pwrseq *p); + bool used; + bool suspended; +}; + +/* used for power sequence instance list in one driver */ +struct pwrseq_list_per_dev { + struct pwrseq *pwrseq; + struct list_head list; +}; + +#if IS_ENABLED(CONFIG_POWER_SEQUENCE) +void pwrseq_register(struct pwrseq *pwrseq); +void pwrseq_unregister(struct pwrseq *pwrseq); +struct pwrseq *of_pwrseq_on(struct device_node *np); +void of_pwrseq_off(struct pwrseq *pwrseq); +int of_pwrseq_on_list(struct device_node *np, struct list_head *head); +void of_pwrseq_off_list(struct list_head *head); +int pwrseq_suspend(struct pwrseq *p); +int pwrseq_resume(struct pwrseq *p); +int pwrseq_suspend_list(struct list_head *head); +int pwrseq_resume_list(struct list_head *head); +#else +static inline void pwrseq_register(struct pwrseq *pwrseq) {} +static inline void pwrseq_unregister(struct pwrseq *pwrseq) {} +static inline struct pwrseq *of_pwrseq_on(struct device_node *np) +{ + return NULL; +} +static void of_pwrseq_off(struct pwrseq *pwrseq) {} +static int of_pwrseq_on_list(struct device_node *np, struct list_head *head) +{ + return 0; +} +static void of_pwrseq_off_list(struct list_head *head) {} +static int pwrseq_suspend(struct pwrseq *p) +{ + return 0; +} +static int pwrseq_resume(struct pwrseq *p) +{ + return 0; +} +static int pwrseq_suspend_list(struct list_head *head) +{ + return 0; +} +static int pwrseq_resume_list(struct list_head *head) +{ + return 0; +} +#endif /* CONFIG_POWER_SEQUENCE */ + +#endif /* __LINUX_PWRSEQ_H */ diff --git a/include/linux/serdev.h b/include/linux/serdev.h index 9f14f9c..2e1eb4d 100644 --- a/include/linux/serdev.h +++ b/include/linux/serdev.h @@ -7,6 +7,7 @@ #include #include +#include #include #include @@ -45,6 +46,7 @@ struct serdev_device { const struct serdev_device_ops *ops; struct completion write_comp; struct mutex write_lock; + char modalias[SERDEV_NAME_SIZE]; }; static inline struct serdev_device *to_serdev_device(struct device *d) @@ -63,6 +65,7 @@ struct serdev_device_driver { struct device_driver driver; int (*probe)(struct serdev_device *); void (*remove)(struct serdev_device *); + const struct serdev_device_id *id_table; }; static inline struct serdev_device_driver *to_serdev_device_driver(struct device_driver *d) @@ -112,6 +115,8 @@ static inline struct serdev_controller *to_serdev_controller(struct device *d) return container_of(d, struct serdev_controller, dev); } +struct serdev_controller *of_find_serdev_controller_by_node(struct device_node *node); + static inline void *serdev_device_get_drvdata(const struct serdev_device *serdev) { return dev_get_drvdata(&serdev->dev); diff --git a/scripts/Makefile.dtbinst b/scripts/Makefile.dtbinst index 50d580d..079b833 100644 --- a/scripts/Makefile.dtbinst +++ b/scripts/Makefile.dtbinst @@ -18,9 +18,10 @@ include scripts/Kbuild.include include $(src)/Makefile dtbs := $(addprefix $(dst)/, $(dtb-y) $(if $(CONFIG_OF_ALL_DTBS),$(dtb-))) +dtbos := $(addprefix $(dst)/, $(dtbo-y) $(if $(CONFIG_OF_ALL_DTBS),$(dtb-))) subdirs := $(addprefix $(obj)/, $(subdir-y) $(subdir-m)) -__dtbs_install: $(dtbs) $(subdirs) +__dtbs_install: $(dtbs) $(dtbos) $(subdirs) @: quiet_cmd_dtb_install = INSTALL $@ @@ -29,6 +30,9 @@ quiet_cmd_dtb_install = INSTALL $@ $(dst)/%.dtb: $(obj)/%.dtb $(call cmd,dtb_install) +$(dst)/%.dtbo: $(obj)/%.dtbo + $(call cmd,dtb_install) + PHONY += $(subdirs) $(subdirs): $(Q)$(MAKE) $(dtbinst)=$@ dst=$(patsubst $(obj)/%,$(dst)/%,$@) diff --git a/scripts/Makefile.lib b/scripts/Makefile.lib index 213677a..6c1d72c 100644 --- a/scripts/Makefile.lib +++ b/scripts/Makefile.lib @@ -283,6 +283,7 @@ DTC_FLAGS += -Wno-interrupt_provider ifeq ($(findstring 1,$(KBUILD_EXTRA_WARN)),) DTC_FLAGS += -Wno-unit_address_vs_reg \ -Wno-unit_address_format \ + -Wno-gpios_property \ -Wno-avoid_unnecessary_addr_size \ -Wno-alias_paths \ -Wno-graph_child_address \ @@ -343,6 +344,18 @@ endef $(obj)/%.dt.yaml: $(src)/%.dts $(DTC) $(DT_TMP_SCHEMA) FORCE $(call if_changed_rule,dtc,yaml) +quiet_cmd_dtco = DTCO $@ +cmd_dtco = mkdir -p $(dir ${dtc-tmp}) ; \ + $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \ + $(DTC) -@ -H epapr -O dtb -o $@ -b 0 \ + -i $(dir $<) $(DTC_FLAGS) \ + -Wno-interrupts_property \ + -d $(depfile).dtc.tmp $(dtc-tmp) ; \ + cat $(depfile).pre.tmp $(depfile).dtc.tmp > $(depfile) + +$(obj)/%.dtbo: $(src)/%.dts FORCE + $(call if_changed_dep,dtco) + dtc-tmp = $(subst $(comma),_,$(dot-target).dts.tmp) # Bzip2 diff --git a/scripts/mod/devicetable-offsets.c b/scripts/mod/devicetable-offsets.c index e377f52..96ed899 100644 --- a/scripts/mod/devicetable-offsets.c +++ b/scripts/mod/devicetable-offsets.c @@ -152,6 +152,9 @@ int main(void) DEVID_FIELD(i3c_device_id, part_id); DEVID_FIELD(i3c_device_id, extra_info); + DEVID(serdev_device_id); + DEVID_FIELD(serdev_device_id, name); + DEVID(spi_device_id); DEVID_FIELD(spi_device_id, name); diff --git a/scripts/mod/file2alias.c b/scripts/mod/file2alias.c index fb48270..57ad7a5 100644 --- a/scripts/mod/file2alias.c +++ b/scripts/mod/file2alias.c @@ -947,6 +947,15 @@ static int do_spi_entry(const char *filename, void *symval, return 1; } +static int do_serdev_entry(const char *filename, void *symval, + char *alias) +{ + DEF_FIELD_ADDR(symval, serdev_device_id, name); + sprintf(alias, SERDEV_MODULE_PREFIX "%s", *name); + + return 1; +} + static const struct dmifield { const char *prefix; int field; @@ -1427,6 +1436,7 @@ static const struct devtable devtable[] = { {"rpmsg", SIZE_rpmsg_device_id, do_rpmsg_entry}, {"i2c", SIZE_i2c_device_id, do_i2c_entry}, {"i3c", SIZE_i3c_device_id, do_i3c_entry}, + {"serdev", SIZE_serdev_device_id, do_serdev_entry}, {"spi", SIZE_spi_device_id, do_spi_entry}, {"dmi", SIZE_dmi_system_id, do_dmi_entry}, {"platform", SIZE_platform_device_id, do_platform_entry}, diff --git a/scripts/package/builddeb b/scripts/package/builddeb index ad30ece..d9eeacc 100755 --- a/scripts/package/builddeb +++ b/scripts/package/builddeb @@ -153,6 +153,7 @@ if is_enabled CONFIG_OF_EARLY_FLATTREE; then # Only some architectures with OF support have this target if [ -d "${srctree}/arch/$SRCARCH/boot/dts" ]; then $MAKE -f $srctree/Makefile INSTALL_DTBS_PATH="$tmpdir/usr/lib/$packagename" dtbs_install + $MAKE -f $srctree/Makefile INSTALL_DTBS_PATH="$tmpdir/boot/dtbs/$version" dtbs_install fi fi